Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Choose a transition effect. .Press the op buttons or turn the – dial to choose an effect, then press the m button. The slideshow will start a few seconds after [Loading image] displays. .In filtered playback (p. 109), only images matching a filter play back. .You can pause/restart a slideshow by pressing the m button again. .Press the nbutton to stop the slideshow. • If you press the qrbuttons or turn the – dial during playback, the image will switch. If you keep the qr buttons pressed, you can fast- forward through images. • The power saving function does not work during slideshows (p. 52). Viewing Slideshows Changing the Settings You can set a slideshow to repeat, or change transition effects and the time that slideshow images are displayed. You can choose from six transition effects when switching between images. Choose [Slideshow]. .Press the n button, choose [Slideshow] from the 1tab and press the m button. Make the setting. .Press the op buttons or turn the – dial to choose an item, and press the qr buttons to adjust the setting. .If you choose [Start] and press the m button, the slideshow starts with your settings. .Pressing the n button will restore the menu screen. You cannot change [Play Time] if [Bubble] is chosen in [Effect]. Checking the Focus You can magnify the area of a recorded image that was inside the AF Frame, or the area of a face that was detected, to check the focus. Press the pbutton, and switch to the focus check display (p. 44). A white frame will appear where the AF frame or face was when the focus was set. A gray frame will appear on a face detected during playback. The area within the orange frame appears magnified. Switch frames. .Move the zoom lever toward k once. The screen shown to the left will appear. .Press the m button to move to a different frame when multiple frames appear. Change the magnification level or location. .Use the zoom lever to change the display size, and the opqrbuttons to change the display position while checking the focus. .Pressing the n button resets the display to Step 1. Magnifying Images Move the zoom lever toward k. .The display will zoom in on the image and, if you continue to hold the zoom lever, it will continue to zoom in up to a maximum factor of 10x. .If you press the opqr buttons, you can move the location of the displayed area. .Move the zoom lever toward g to zoom out, or continue to hold it to return to Single Image Playback. Approximate Location .If you turn the –dial, you can switch of Displayed Area images in the zoomed state. Pressing the nbutton while magnifying images restores Single Image Playback. Changing Image Transitions You can choose from three transition effects when switching between images in Single Image Playback. Choose [Transition]. .Press the nbutton and choose the 1 tab, then choose [Transition] and press the qr buttons to choose a transition effect. What if the images don’t properly display on the TV? What if the images don’t properly display on the TV? Viewing Images on a TV Using the supplied stereo AV cable (p. 2), you can connect the camera to a TV to view images you have shot. Yellow White Yellow Red Red White Turn off the camera and TV. Connect the camera to the TV. .Open the camera’s terminal cover and fully insert the cable plug into the camera’s terminal. .Insert the cable plug fully into the video input terminals as shown in the illustration. Turn on the TV and switch it to the input to which the cable is connected. Turn on the camera. .Press the 1button to turn on the camera. The image will appear on the TV (nothing will appear on the screen of the camera). .After you finish, turn off the camera and TV, and unplug the cable. Images will not display correctly if the camera’s video output setting (NTSC/PAL) does not match the TV system. Press the n button, choose the 3 tab and [Video System] to switch to the correct video system. Viewing Images on a High-Definition TV Use the separately sold HDMI Cable HTC-100 to connect the camera to a high-definition TV for an enhanced viewing experience. Turn off the camera and TV. Connect the camera to the TV. .Open the cover and fully insert the cable plug into the camera’s HDMI terminal. .Fully insert the cable plug into the TV’s HDMI terminal. .Follow Steps 3 and 4 on p. 115 to display the images. Operation sounds will not play when connected to a high-definition TV. Displaying Various Images (Smart Shuffle) The camera will choose four images based on the displayed image. If you choose one of those images, the camera will choose four more images letting you enjoy the playing back of images in an unexpected order. This will work best if you take many shots of various scenes. Choose . .Press the m button, choose in the omenu, then press the m button again. Four images will appear as candidates. Choose an image. .Press the opqr buttons to choose the image you want to view next. The chosen image will be displayed in the middle, and the next four candidates will appear. ...