Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
-5: Only takes the color that you want to change. +5: Also takes colors close to the one that you want to change. 3 Aim the camera so that the desired color appears atthe center of the LCD monitor (or viewfinder) andpress the .. button. • Only one color can be specified. 4 Complete the setting with the SET button, and shoot. • This completes the setting. • When you press the Movie button, you can shoot movies in Color Swap mode. • The default setting for Color Swap changes green into white. • You may not obtain the expected results after color input mode if you use the flash. • The colors specified in the Color Swap mode are retained even if the camera's power is turned off. Using the Mode Dial 55 Saving Original Images Not only can you save images with altered colors when shooting still images with the Color Accent or Color Swap modes, but you can also choose to save the original images (before the color change). 1 (Rec.) menu [Save Original] [On]/[Off]*. See Menus and Settings (p. 27) • If [On] is selected, the images will be saved as consecutive file numbers. The original image will be the lower file number, while the image shot in Color Accent or Color Swap mode will be the higher file number. * Default setting. If [Save Original] is set to [On] • Only the image set with Color Accent or Color Swap is displayed on the LCD monitor (or viewfinder) during shooting. • The image displayed on the LCD monitor (or viewfinder) immediately after shooting is the one shot with Color Accent or Color Swap (pp. 53, 54). As erasing the image at this time will cause the original image to be erased at the same time, be careful. • As two images are saved with each shot, the number of recordable shots displayed on the LCD monitor (or viewfinder) will be half the number that is displayed when [Save Original] is set to [Off]. Shooting in the Creative Zone Shooting Mode You can freely select camera settings such as the shutter speed and aperture value to suit your shooting purposes. After settings are made, shooting procedures are the same as for Auto Mode (Basic Guide p. 6). • For information on the relation between the aperture value and shutter speed see p. 58. • Please note that camera shake becomes a factor at low shutter speeds and with larger aperture values. If (camera shake warning) appears in the LCD monitor (or viewfinder), try the following steps to resolve the problem. -Use the (image stabilizer) function. -Raise the ISO speed. -Raise the flash to enable firing. -Use a tripod. Program AE Using the Mode Dial Shooting Mode Use the program AE mode to have the camera automatically set the shutter speed and aperture value to match the brightness of the scene. • When a correct exposure cannot be obtained, the shutter speed and aperture values are shown in red on the LCD monitor when the button is pressed halfway. Use the following shooting methods obtain the correct exposure and make them show in white. -Use the flash (raise the flash). -Adjust the ISO Speed. -Change the metering mode. You can change the combinations of shutter speeds and aperture values without altering the exposure (p. 70). 57 Setting the Shutter Speed Shooting Mode When you set the shutter speed in the shutter speed-priority AE mode, the camera automatically selects an aperture value to match the brightness. Faster shutter speeds allow you to catch an instantaneous image of a moving subject, while slower speeds create a flowing effect and allow you to shoot without a flash in dark areas. 1 Use the .. or • button to select the shutter speed, then shoot. • If the aperture value is shown in red, the image is underexposed (insufficient light) or overexposed (too much light). Use the .. or • button to adjust the shutter speed until the aperture value shows in white. ..The nature of CCD image sensors is such that noise in the recorded image increases at slow shutter speeds. This camera, however, applies special processing to images shot at shutter speeds slower than 1.3 seconds to eliminate the noise, thereby producing high-quality images (Nevertheless, a certain amount of processing time may be required before the next image can be shot). ..The aperture value and shutter speed change according to the zoom state as follows. Aperture value Shutter Speed (seconds) Maximum Wide Angle *1 F 2.7 – 3.5 to 1/1600 F 4.0 – 5.0 to 1/2000 F 5.6 – 7.1 to 1/2500 F 8.0 to 1/3200 Maximum Telephoto*2 F 3.5 – 4.5 to 1/1600 F 5.0 – 6.3 to 1/2000 F 7.1 – 8.0 to 1/2500 *1 Maximum wide angle setting *2 Maximum telephoto setting ..The fastest shutter speed for flash synchronization is 1/500 second. The camera automatically resets the shutter speed to 1/500 second if a faster speed is selected. Shutter Speed Display ..The numbers in the table below indicate the shutter speed in seconds. 1/160 indicates 1/160 second. Also, quote marks indicate the decimal place, so that 0"3 indicates 0.3 second and 2" indicates 2 seconds. 15" 13" 10" 8" 6" 5" 4" 3"2 2"5 2" 1"6 1"3 1" 0"8 0"6 0"5 0...