Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Flash is enabled. • Push down the flash to disable it. A bar of light (red, purple) appears on the LCD monitor Subject is too bright. • This is a normal occurrence in devices containing CCDs and does not constitute a malfunction. (This red bar of light will not be recorded when shooting still photos, but it will be recorded when shooting movies.) Noise displays on the LCD monitor. Subject's movements on LCD monitor are irregular. Camera automatically lightened the image displayed on the LCD monitor to make it easier to see when shooting in a dark area. • There is no effect on the recorded image. ..See Night Display (p. 28) White dots appear on the image. Light from the flash has reflected off dust particles or insects in the air. This occurs more frequently in the following conditions: • When shooting at the wide angle end. • When shooting with a high aperture value in the aperture-priority AE mode. • This is a phenomenon that occurs with digital cameras and does not constitute a malfunction. Flash does not fire Flash is set to off. • Raise the flash so that it can fire. ..See Using the Flash (p. 40) Image not showing on TV monitor Incorrect video system setting. • Set the video system to the appropriate setting, NTSC or PAL, for your TV. Shooting mode set to (Stitch Assist). • The output will not appear on a TV monitor in (Stitch Assist) mode. Cancel the Stitch Assist mode. Reading images from the memory card is slow, or recording images to the memory card takes a long time Memory card was formatted in another device. • Use a memory card formatted with this camera. ..See Formatting a Memory Card (p. 20) Appendix 10 155 Using Conversion Lenses (Sold Separately) Conversion Lens Adapter LA-DC58E and Lens Hood LH-DC40 are included in the separately sold Lens Adapter/Hood Kit LAH-DC20. The camera supports use of the separately sold Wide Converter WCDC58A, Tele-converter TC-DC58B and close-up lens 500D (58cm). In order to attach any of these lenses, you also need to use the separately sold Conversion Lens Adapter LA-DC58E (included with LAH-DC20). When shooting in backlit conditions without the flash and at the wide angle end, the use of the lens hood is recommended to prevent external light from entering the lens. Warning • When attaching the wide converter, tele-converter or close-up lens, be sure to screw it on securely. If they come loose, they may fall from the lens adapter, posing risk of injury from shattered glass. • Never look into the sun or into strong light through the wide converter, teleconverter or close-up lens as this can result in blindness or impairment of vision. • If the built-in flash is used with the lens hood attached, the outer edges of shot images (especially the lower right) may be darkened. • When using the wide converter, set the camera to the maximum wide angle. • When using the tele-converter, set the camera near the maximum telephoto. At other zoom settings, the image will appear as if its corners have been cut off. • Filters and lens hoods cannot be attached to the wide converter and tele-converter lens. 157 Appendix 10 Attaching a Lens/Lens Hood 1 Be sure that the camera is turned off. Press the ring release button and hold it down, turn the ring in the direction of the arrow and remove it. 2 Align the .. marks on the conversion lens adapter and the .. mark on the camera, and turn the adapter in the direction of the arrows as far as the .. mark on the camera. .. To remove the conversion lens adapter (for the lens hood or conversion lens), turn the adapter in the opposite direction while holding down the ring release button. 3 Set the lens or lens hood on the adapter, and attach it securely by turning it in the indicated direction. Ring Release Button Ring Conversion Lens Adapter LA-DC58E when attached. Wide Converter WC-DC58A when attached. • You should not shoot images in (Stitch Assist) mode when using these attachments. Although it is possible to select this mode on the camera, the PhotoStitch software will not be able to stitch the images together on the computer. • To protect the conversion lens, hold the camera's lens with one hand and screw the conversion lens onto the camera with the other hand. • Completely remove all dust and dirt from conversion lenses with a lens blower brush before use. The camera may focus on any dirt that remains. • Be careful when handling the lenses so as not to get fingerprints on them. • Once the lens adapter is screwed on the camera, it locks into place. When removing the wide converter, the tele-converter or the close-up lens, do so while firmly pressing on the lens adapter with your hand to avoid damage to the lenses. Converter Settings Set the camera appropriately after attaching the Wide Converter WCDC58A or the Tele-converter TC-DC58B (no setting is needed for the 500D Close-Up lens). 1 Select [Converter] from the [ (REC)] menu. 2 Use the .. or .. button to select the attached converter. 3 Press the MENU button. When Image Stabilizer is ...