Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
• You can use an NP-FM500H battery pack only. Make sure that the battery is NP-FM500H. The remaining battery indicator is incorrect, or sufficient remaining battery indicator is displayed but the power runs out too quickly. Cannot turn on the camera. • This phenomenon occurs when you use the camera in an extremely hot or cold location (page 198). • The battery pack is discharged. Install a charged battery pack (page 20). • The battery pack is dead (page 209). Replace it with a new one. • Install the battery pack correctly (page 22). The power turns off suddenly. • If you do not operate the camera for given period of time, the camera turns to power saving mode and nearly shuts down. To cancel the power save, 187 Trouble Others (Advanced Troubleshooting Troubleshooting (page 164). The CHARGE lamp flashes when charging the battery pack. • You can use an NP-FM500H battery pack only. Make sure that the battery is NP-FM500H. • If you charge a battery pack that has not been used for a long time, the CHARGE lamp may flash. • The CHARGE lamp flashes in 2 ways, fast (about 0.15-second intervals) and slow (about 1.5-second intervals). If it is flashing fast, remove the battery pack and reattach the same battery pack securely. If the CHARGE lamp flashes fast again, it suggests that there is something wrong with the battery pack. Slow flashing indicates that charging is suspended because the ambient temperature is outside the suitable range for charging the battery pack. Charging will resume and the CHARGE lamp will be lit when the ambient temperature returns to within the suitable temperature. Charge the battery pack under the suitable temperatures between 10°C and 30°C (50°F and 86°F). Shooting images Nothing is displayed on the LCD monitor in viewfinder mode when the power is turned on. • If you do not operate the camera for given period of time, the camera turns to power saving mode and nearly shuts down. To cancel the power save, operate the camera, such as pressing the shutter button halfway down (page 164). The image is not clear in the viewfinder. • Adjust the diopter scale properly using the diopter-adjustment dial (page 30). No images in the viewfinder. • [FINDER/LCD Setting] is set to [Manual]. Press the FINDER/LCD button (page 164). • Move your eye a little closer to the viewfinder. 188 Troubleshooting Troubleshooting • You are using a memory card with a write-protect switch, and the switch is set to the LOCK position. Set the switch to the recording position. • Check the free capacity of the memory card. • You cannot record images while charging the built-in flash (pages 42, 124). • In autofocus mode, the shutter cannot be released when the subject is out of focus. • The lens is not attached properly. Attach the lens properly (page 25). • When the camera is attached to another device, such as an astronomical telescope, set [Release w/o Lens] to [Enable] (page 160). • The subject may require special focusing (page 109). Use the focus-lock or manual focus function (pages 110, 114). Recording takes a long time. • The noise reduction function is turned on (page 159). This is not a malfunction. • You are shooting in RAW mode (page 157). Since the RAW data file is large, the RAW mode shooting may take time. • The Auto HDR is processing an image (page 128). The same image is shot several times. • The drive mode is set to [Cont. Shooting] or [Bracket: Cont.]. Set it to [Single Shooting] (pages 46, 139). • The exposure mode is set to Continuous Advance Priority AE (pages 41, 93). • The exposure mode is set to AUTO+ and [Auto+ Image Extract.] is set to [Off] (page 88). The image is out of focus. • The subject is too close. Check the minimum focal distance of the lens. • You are shooting in manual focus mode, set the focus mode switch to AF (autofocus) (page 108). • When the focus mode switch is equipped with the lens, set it to AF. • Ambient light is insufficient. Trouble Others (Advanced Eye-Start AF does not work. • Set [Eye-Start AF] to [On] (page 80). • Press the shutter button halfway down. 189 Troubleshooting Troubleshooting • The flash mode is set to [Autoflash]. If you want to make sure the flash fires without fail, set the flash mode to [Fill-flash] (pages 42, 124). The flash takes too long to recharge. • The flash has been fired in succession in a short period. When the flash has been fired in succession, the recharging process may take longer than usual to avoid overheating of the camera. A picture taken with the flash is too dark. • If the subject is beyond the flash range (the distance that the flash can reach), the pictures will be dark because the flash light does not reach the subject. If the ISO is changed, the flash range also changes with it. Check the flash range in “Specifications.” The date and time are recorded incorrectly. • Set the correct date and time (page 28). • The area selected with [Area Setting] is different from the actual area. Set up [Area Setting] again (page 28). The aperture val...
Dieses Handbuch ist für folgende Modelle:Kameras - SLT-A65V (2.59 mb)
Kameras - SLT-A65K (2.59 mb)
Kameras - SLT-A65M (2.59 mb)
Kameras - SLT-A65VK (2.59 mb)