Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Cleaning the scan unit Keeping the scan unit clean helps ensure the best possible copies. We suggest that you clean the scan unit at the start of each day and during the day, as needed 1. Slightly dampen a soft lint-free cloth or paper towel with water. 2. Open the control panel by gripping it on the bottom edge and pulling it upwards. 3. Disassemble the white roller as follows The right end of the white roller has a plastic bush that is snapped shut with small tab on it. Pull the tab inward slightly then lift the tab until the roller is released. Lift the roller upwards and to the right, releasing the left end of the roller, then rotate the bushing until it reach a slot. Then pull the roller upward. 4. Wipe the roller surface with a soft cloth dampened with water. 5. Carefully wipe the scanning glass with a soft dry cloth. If the glass is very dirty, first wipe it with a slightly dampened cloth, and then with a dry cloth. Be very careful not to scratch the glass surface. 6. Replace the roller by inserting the left end first followed by the right end, then rotating the bushing until it locks into place. 7. Reconnect the support and the control panel and then close the control panel firmly until it clicks into place. Cleaning the drum If there are streaks or spots on your machine, the OPC drum of the cartridge may require cleaning. 1. Before setting the cleaning procedure, make sure that paper is loaded in the machine. 2. Press Menu until Maintenance appears. 3. Press the left/right arrow until Clean Drum appears and press OK. 4. Press the left/right arrow until On appears and press OK. The machine prints a cleaning page. Toner particles on the drum surface are affixed to the paper. 5. If the problem remains, repeat step 1 through 4. Storing the Toner cartridge • Inside the protective bag from the original package. • Store lying flat (not standing on end) with the same side facing up as if they were installed in the machine. • Do not store consumable in; - Temperature greater than 40°C (104°F). - Humidity range less than 20% nor greater than 80%. - An environment with extreme changes in humidity or temperature. - Direct sunlight or room light. - Dusty places. - A car for a long period of time. - An environment where corrosive gases are present. - An environment with salty air. Handling instructions • Do not touch the surface of the photosensitive drum in the cartridge. • Do not expose the cartridge to unnecessary vibrations or shock. • Never manually rotate the drum, especially in the reverse direction; this can cause internal damage and toner spillage. Use of non-Samsung and refilled toner cartridge Samsung Electronics does not recommend or approve the use of non-Samsung brand toner cartridges in your printer including generic, store brand, refilled, or remanufactured toner cartridges. Estimated cartridge life Estimated cartridge life (the life of the toner cartridge yield) depends on the amount of toner that print jobs require. The actual print-out number may vary depending on the print density of the pages you print on, operating environment, printing interval, media type, and/or media size. For example, if you print a lot of graphics, the consumption of the toner is high and you may need to change the cartridge more often. Tips for moving & storing your machine • When moving the machine, do not tilt or turn it upside down. Otherwise, the inside of the machine may be contaminated by toner, which can cause damage to the machine or bad print quality. 8. Troubleshooting This chapter gives helpful information for what to do if you encounter an error. This chapter includes: • Redistributing toner • Clearing original document jams • Tips for avoiding paper curls • Tips for avoiding paper jams • Clearing paper jams • Understanding display messages • Solving other problems Redistributing toner • White streaks or light printing occurs. • Prepare new cartridge appears on the display. • The Status LED blinks red. 1. Open the front door. 2. Pull the toner cartridge out. 3. Thoroughly roll the cartridge five or six times to distribute the toner evenly inside the cartridge. 4. Hold the toner cartridge by the handle and slowly insert the cartridge into the opening in the machine. Tabs on the sides of the cartridge and corresponding grooves within the machine will guide the cartridge into the correct position until it locks into place completely. 5. Close the front door. Ensure that the cover is securely closed. Clearing original document jams Input Misfeed 1. Remove any remaining pages from the document feeder. 2. Pull the jammed document gently out of the document feeder. 3. Load the documents back into the document feeder. Exit Misfeed 1. Remove any remaining pages from the document feeder. 2. Open the control panel by gripping it on the bottom edge and pulling it. 3. Pull the document gently out of the document feeder. 4. Close the control panel. Then load the documents back into the document feeder. Tips for avoidin...
Dieses Handbuch ist für folgende Modelle:Drucker - CF-650 (4.11 mb)
Drucker - SF-651 (4.11 mb)