Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Heath Zenith Dateigröße: 502.4 kb Dateiname: Unterrichtssprache:

2. Install the 3 alkaline "D" batteries. Make sure the batteries are oriented properly. 3. Before mounting, test the doorbell range. Put the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Operation Press the doorbell button to verify that the doorbell and chime work properly. If the chime does not sound see the Troubleshooting guide on page 4. 4. Mount the doorbell button and chime. Use either screws or double sided tape to mount the doorbell button. To mount with screws, remove the back of the case by pushing in the tab on the bottom with a small screwdriver. © 2003 DESA Specialty Products™ 595-5611-05 Attach the back of the case to the door jamb or wall. Snap the front of the button back on. When attaching the doorbell button using the double sided tape, make sure the surface of the door jamb or wall is clean. The chime can be mounted by using the 3 holes in the back of the case, or by using 2 screws with the keyholes. 3-5/16" (84 mm) Chime Back Case Keyhole Mounting Chime Back Holes for Wall Mounting Case Mounting Close Chime Case Snap the front of the chime case back on. Start with the top edge of the case aligned with the top of the back plate. Code and Tune Settings Code Settings Note: Most installations will not require you to change any of the jumpers on your doorbell. The doorbell button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the doorbell button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Another wireless doorbell system or other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Disconnect the power to the doorbell button and chime. 2. Open the cases and locate the jumpers on both the doorbell button and chime (See illustration). -2-595-5611-05 3. The doorbell button and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code. 4. To change the code, add and/or remove jumpers as needed. There are 128 different combinations. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the doorbell button and chime for this system to function. Tune Settings Your Heath®/Zenith wireless doorbell has 3 different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note). The factory setting is for the Westminster; however, this can be changed by following the instructions below. • Ding (one note tune) Doorbell button: Add a jumper to location 8. • Ding-Dong (two note tune) Doorbell button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) Doorbell button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: Model 6162 has doorbell buttons for both front and back door. The back door must use the Ding tune and the front door may use either the Ding-Dong or Westminster tune. eryBattery eryBattery BBattery 12 345 67812 345 678 Doorbell Button Battery Replacement Install an alkaline type A23 12 Volt battery. The positive terminal should be positioned as shown. * Code Settings 1-7 Must Match Both Doorbell Button and Chime Inside Doorbell Button Tune Setting Inside Chime 595-5611-05 -3 Troubleshooting Chime does not sound: • Make sure the doorbell button and the chime codes are the same (See pages 2 and 3). • Check orientation of doorbell button battery (See page 3). • Check the doorbell button and chime batteries, replace if necessary. Batteries seem OK, but the chime does not work when installed: • Do not mount the chime or doorbell button on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move the chime or doorbell button off the metal surface. • Don't mount the chime too close to ground level concrete slabs. This may also reduce the range. Mount the chime away from the floor. •Try different locations for the chime closer to the doorbell button. Also try to orient the chime at a different angle to increase the range. The range of the doorbell depends on location, temperature and battery condition. Technical Service (Do Not Send Products) If you experience a problem, follow this guide. You may also want to visit our Web site at: If the problem persists, call* for assistance at 1800- 858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to: DESA Specialty Products™ P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service Specialty Products * If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase. No Service Parts Available for this Product Regulat...

Herunterladen

Geben Sie zwei Ziffern: