Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
REVISION HISTORY 3 GETTING STARTED . . . 42. SYSTEM DESCRIPTION 4 FEATURES 4 DEFINITIONS 4 1. SYSTEM INSTALLATION 5 a. ST300-S/SM, VTR/DDR CONTROLLER 5 b. PRODUCTION SWITCHER 5 2. VIDEO SERVER SETUP 7 3. LOAD A CLIP 7 4. LEARN ON THE ST300 7 7. LEARN ON THE PRODUCTION SWITCHER 8 8. RECALL ON THE ST300 8 9. RECALL ON THE PRODUCTION SWITCHER 8 10. PBIO ENABLE/DISABLE 9 11. TRIGGERS FROM THE PRODUCTION SWITCHER 9 ADVANCED FEATURES . . . 1011. CREATE NEW CLIPS 10 12. LOOP A CLIP 10 13. SETTING THE IN (OUT) POINT 11 a. MARKING THE IN (OUT) POINT 11 b. VIEWING THE IN (OUT) POINT 11 c. CLEARING AN IN (OUT) POINT 11 14. TRIM CLIPS 11 15. VIEW CONTENTS OF CUE POINT 12 16. TRANSFERRING CUELIST 12 a. TRANSMIT CUE LIST FUNCTION 12 b. RECEIVE CUELIST FUNCTION 13 REFERENCE . . . 1417. SETUP MENU 14 18. FUNCTION TABLE 16 19. SPECIFICATIONS 17 ST300 17 20. KEY LAYOUT 19 21. DNF CONTROLS LIMITED WARRANTY 20 Manual Version.............................................................3.6 080604 Document No.....…......... 4000CL-MAV-PBIO_User_ Manual.doc 1. REVISION HISTORY 120602 Rev. 3.0 Added GPI’s 040303 Rev. 3.1 Added Key Layout 100903 Rev. 3.2 Company header information revised. 112503 Rev. 3.3 Updated Transmit Cue List Function and Receive Cue List Function description. Changed Key Layout. Added DNF Controls Limited Warranty. 121003 Rev. 3.4 Added LOOP A CLIP Section. Revised TRIM CLIPS Section. Added Video Sync, Video Standard, Recall Menu Options. 020504 Rev. 3.5 Added note to cover: Supports up to 4 Video Server Channels. 080604 Rev. 3.6 Added T-bar dimension. Getting Started . . . 2. SYSTEM DESCRIPTION .. NOW, production switchers can load & play video clips on Sony MAV DDRs. .. Use the EMEM or SNAPSHOT Learn & Recall functions of the production switcher to load and play a video clip from a Recall or timeline. .. Use the Run and Trigger functions of the production switcher to Play, Stop or Recue the video clip. .. Instantly load a video clip at the press of a button. .. Instantly load a FILL clip & KEY clip at the press of ONE button, then play out both channels in sync. LOOP up to 4 channels. .. Control up to 4 video channels individually or ganged. FEATURES The 4000CL-MAV-PBIO, 400 Clip Instant Access System consists of the ST300-SSM with Cliplist software. With this Option, the ST300 has 4 Peripheral Device Addresses, one for each VTR that it controls. This allows the production switcher to control any and all VTRs connected to the ST300. Upon receipt of the Learn command from the production switcher, the ST300 saves the CLIP IDs of the currently loaded clips, the current time of each clip, the VTRs they are loaded on, and the current GANG mode, into the appropriate Cue Point. When the Recall command is received, the ST300 loads the “Learned” Clips onto the “Learned” VTRs, cues the Clip to the “Learned” time, then restores the “Learned” GANG mode. The Trigger function on the production switcher puts the selected VTRs into Play, Stop, Recue or other available modes. DEFINITIONS .. Throughout this document, “Video Server” refers to the MAV-555. .. The ST300-S/SM as the ST300. .. Words surrounded by brackets, for example, [ENTER], are keys on the ST300. [XXX] + [XXX] means hold the two keys down simultaneously. .. “Softkeys” are the row of keys directly below the display that perform multiple functions in MENU and other modes. 1. SYSTEM INSTALLATION a. ST300-S/SM, VTR/DDR CONTROLLER 1) Plug one end of a 9-conductor, RS422 serial cable into the 9-pin connector (VTR 1, 2, 3 or 4) on the rear of the ST300. Plug the other end of the cable into the 9-pin REMOTE connector on the Video Server. 2) Connect the +5, +12, -12 VDC POWER SUPPLY into the POWER connector on the rear of the ST300. Plug the Power Supply into an outlet, 90 VAC to 240 VAC. 3) Check SETUP MENU prior to using the ST300 to confirm proper Record mode and other User settable modes. b. PRODUCTION SWITCHER 1) Connect a standard cable (RS422, 9-pin serial cable) to the “AUX” connector on the rear of the ST300. Connect the other end of the cable to the Peripheral Bus Connector on the production switcher. (Communication Format- 38.4K, N, 8,1) 2) The ST300 has 4 Peripheral Device Addresses, one for each VTR that it controls. To set the Device Address for each VTR: a) Press [MENU] and turn the Wheel until “Peripheral Address” is displayed. b) Press VTR[1], VTR[2], VTR[3] or VTR[4] to select a VTR. c) Assign a Peripheral Device Address for that VTR, from 0 to 23, by entering the desired address using the numeric keypad. NOTE: Address 24 or greater will turn PBIO off. d) Select the next VTR, and then assign a Peripheral Device Address for it. Each VTR must have its own unique address. 3) To select a Production Switcher type (Default = Grass Valley Group). a) Press [MENU] and turn the Wheel until “SWITCHER” is displayed. b) Press the Softkeys to toggle between Sony and Grass Valley. 4) For version 3.0 hardware, there is an option to set Parity to match the parity of t...