Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
After you have finished reading the instructions, put them away in a safe place for future reference. K015 En WARNING This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture. D3-4-2-1-3_A_En WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm. Wash hands after handlingD36-P4_En The Generation of Acoustical Noise Is Less Than 70dB. (ISO7779/DIN45635) CAUTION This product is a class 1 laser product, but this product contains a laser diode higher than Class 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel. The following caution label appears on your unit. Location: on top of the cover D3-4-2-1-8_A_En CLASS 1 LASER PRODUCT LASER KLASSE 1 IMPORTANT NOTICE – RECORD THE MODEL NUMBER AND SERIAL NUMBERS OF THIS EQUIPMENT BELOW. THE NUMBERS ARE ON THE REAR. MODEL NO.DVR-A08XLA, DVR-A08XLB, DVR-A08XLC SERIAL NO. KEEP THESE NUMBERS FOR FUTURE USE. D1-4-2-6-2_En is a trademark of DVD Format/Logo Licensing Corporation. En SAFETY INSTRUCTIONS To ensure your personal safety and to maximize the full operating potential of your Drive, read and follow these safety precautions: ENVIRONMENT -Avoid installing the unit in a location that is exposed to high temperatures, high humidity, large quantities of dust, or subject to excessive vibrations and shocks. POWER -Turn off the system before installing this unit or any other hardware device. READ AND RETAIN INSTRUCTIONS -Read all safety and operating instructions before operating the unit. CLEANING -Use a damp cloth to clean the exterior housing. Avoid using any fluids including aerosol, liquid, or alcohol-based cleaning products. WATER AND MOISTURE -DO NOT use this product near open containers or other possible sources of liquid. POWER SOURCES -Operate this product only from the recommended power sources. If you are unsure of the type of power available, consult an Authorized Pioneer Dealer. OVERLOADING -DO NOT overload wall outlets and extension cords. Doing so can result in fire or electric shock. OBJECT AND LIQUID ENTRY -Never push objects of any kind into this product. Touching dangerous voltage points may cause a short resulting in fire or electric shock. Do not spill any type of liquid on this product. CONDENSATION -Moisture can form inside of the unit if it is moved between cool surroundings and a warm environment. If you are moving the unit to a different room, leave the product disconnected in the new location for up to 2 hours before installing the unit or turning it back on. SERVICING -Do not attempt to repair this product yourself. Opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. (Refer to the enclosed Service and Support Card.) English .Remove dust or lint from the disc with a soft cloth by wiping from the inside to the outside edge rather than in a circular motion. .Do not use record-cleaning or anti-static agents as the solutions may damage a disc. Always store discs in proper DVD-R storage cases when not in use. Check for dirt, dust, or fingerprints on a disc's recording side before inserting in to the unit. .Avoid touching or scratching the signal surface (shiny side) of the disc. .Hold the disc by the edges or by the center hold and one edge. .Do not affix paper or labels to the disc. .Discard warped or cracked discs as they may cause damage to the drive. .Avoid specially shaped discs such as hearts or polygons. 5 En INTERFACE FRONT VIEW English 1 Forced Ejection Hole If the tray fails to eject when the Eject button is pressed, insert a stiff rod into the hole and push to eject the tray. During normal operation, the eject button should be used to unload the tray. Make sure the power to the drive is turned off and wait at least one minute until the disc stops spinning when forcing the tray to eject using the eject hole. 2 BUSY Indicator Operation status is indicated as follows. During reading Lights During writing Lights 3 Eject Button (0) To unload /load the disc, press the button. 4 Disc Tray Open the loading tray by pressing the eject button, then place a CD or DVD disc onto the tray with the label facing up. Press the eject button or push the front tray panel to load the disc. Do not attempt to pull out the disc tray forcibly. Precautions on playing 8 cm (3.15") Discs An 8cm (3.15") disc cannot be played when the drive isverticaleven if an adapter is attached. ABOUT REGION CODES The region code can only be changed 5 times, including the initial setting. Please be aware that the fifth change becomes PERMANE...