17, located in the machine base. Fig. 17 OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPPING DRILL PRESS The switch (A) Fig. 18, is located on the front of the drillpress head. To turn the drill press “ON” move the switch up to the “ON” position. To turn the drill press “OFF” move the switch down to the “OFF” position. 10 R Q Fig. 15 S T Fig. 16 A A Fig. 18 LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the machine is not in use, the switchshould be locked in the “OFF” position to pre

For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). FRANCAIS : PAGE 34 10" Bench Drill Pre s s (Model SM300) PART NO. 638517-00 10-30-05 Copyright © 2005 Delta Machinery ESPANOL: PAGINA 18 To learn more about DELTA MACHINERYvisit our website at: For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). FRANCAIS : PAGE 34 GENERAL SAFETY RULES Woodworking can be dangerous if safe and prope

#ts10556 printed in taiWan .........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Refer to Operating Instructions-S witch. • Hold drill firmly to control the twisting action of the drill. If your drill is equipped with a side handle, always use the side handle. AWARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other m

#TR8234 PRINTED IN CHINA. ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Oil Bottle..................................................... 1 D. T-Nuts......................................................... 2 E. Chuck Key .................................................. 1 F. End Wrenches 8/10, 14/17, 17/19mm .... 1 ea G. Spindle Spanner Wrench ........................... 1 H. Hex Wrench Set 3, 4, 5, & 6mm ........... 1 ea I. Drawbar Hex Wrench ................................. 1 A B Figure 3. G0619 out of the crate. E H F I C G D Figure 4. Inventory. In the event th

The batteries can explode in a fire. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin - a.Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention

3. Carefully lay the column/base on its side. 4. Slide the column all the way into the bottom of the headstock (approximately 4"-6"). base in the fully upright position. If the base starts to slide when tilting, you MUST have a third person hold the base from sliding to avoid personal injury or machine damage. Figure 12. Tilting drill press upright. -20 G7947/G7948 12 Speed Floor Drill Press 6. Suspend a plum bob from the center of the headstock spindle so it is over the tape/ruler as shown in F

Put on heavy leather gloves to protect your the side of the head stock so the cover stays hands from possible lacerations if the spring splined with the locking lug; loosen the jam uncoils during the next step. nut and loosen the cover nut approximately 1.4" (see Figure 43). 5. Pull the cover outward just enough to disengage the spring-cover lock slot from the locking lug. Note: It is important to keep a good grip during this step. Letting go of the cover will cause the spring to rapidly uncoil.

....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................