Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
3. Carefully lay the column/base on its side. 4. Slide the column all the way into the bottom of the headstock (approximately 4"-6"). base in the fully upright position. If the base starts to slide when tilting, you MUST have a third person hold the base from sliding to avoid personal injury or machine damage. Figure 12. Tilting drill press upright. -20 G7947/G7948 12 Speed Floor Drill Press 6. Suspend a plum bob from the center of the headstock spindle so it is over the tape/ruler as shown in Figure 13. 7. Center the headstock directly over the base as indicated by the plum bob and ruler. Figure 13. Aligning headstock with base. 8. Tighten the two headstock setscrews to the column, as shown in Figure 14. Figure 14. Securing headstock to column. Drill Chuck & Arbor The drill chuck attaches to the spindle by means of the arbor, shown in Figure 15. Matched tapers on the arbor and the inside of the chuck create a semipermanent assembly when properly joined. Figure 15. Chuck components. Drill Chuck Chuck Key Arbor Drift Key To assemble the drill chuck and mount it to the spindle: 1. Use mineral spirits to thoroughly clean the drill chuck, arbor, and spindle sockets and dry all surfaces before assembly. Follow all safety warnings on the container of the mineral spirits. Failure to clean the mating surfaces may cause the tapered fit to loosen during operation, resulting in separation and an unsafe condition. 2. Use the chuck key to adjust the jaws of the drill chuck until they are inside the drill chuck body. 3. Place the drill chuck face down on a workbench. The arbor has a short taper and a long taper. Place the short taper into the socket in the back of the drill chuck and tap it with a rubber or wooden mallet, as shown in Figure 16. If the chuck fails to remain secure on the arbor, repeat Steps 1 & 2. -21 G7947/G7948 12 Speed Floor Drill Press Tang-Side Up Tang-Side Up Figure 16. Seating arbor into chuck. 4. Slide the arbor into the spindle socket while slowly rotating the drill chuck. The socket has a rectangular pocket where the tang (or flat portion of the arbor shown in Figure 16) fits into. 5. Seat the chuck with a rubber mallet, as shown in Figure 17. DO NOT use a steel hammer on the drill chuck to seat the arbor into the spindle. You will damage the chuck and/or spindle, which may make them unusable or unsafe. Figure 17. Seating arbor and chuck into spindle. Downfeed Handles & Belt Cover Knob Components and Hardware Needed: Qty Downfeed Handles .............................................3 The downfeed handles must be installed to properly operate the drill press. To install the downfeed handles: 1. Thread the handles into the spindle hub, as shown in Figure 18, and tighten. 2. Remove the screw that fastens the belt cover in place and install the belt cover knob in its place (see Figure 18 for location). Figure 18. Downfeed handles and belt cover knob installed. Belt Cover KnobSpindle Hub -22 G7947/G7948 12 Speed Floor Drill Press Table Components and Hardware Needed: Qty Table...................................................................1 The table must be installed to properly support the workpiece during operation. To install the table: 1. Insert the table shaft into the table support assembly. 2. Tighten the small locking lever to secure the table in the table support assembly. The table should now be installed as shown in Figure 19 or 20, depending on your model. Light (110V Only) Components and Hardware Needed: Qty 60 W Light Bulb..................................................1 The Model G7947/G7948 includes a light socket, intended for 110V usage only. When the drill press is shipped from the factory, a dust plug is installed in the light socket for protection. To install a light bulb in the drill press: 1. Remove the dust plug from the light socket. 2. Install a 60W or smaller light bulb in the location shown in Figure 21. Figure 19.G7947 table installed. Figure 21. Light bulb access location. Light Bulb Access Here Using light bulbs at 220V will destroy or explode the light bulbs because the light socket is not wired or intended to be wired for 220V. Figure 20. G7948 table installed. -23 G7947/G7948 12 Speed Floor Drill Press Test Run Once assembly is complete, you are ready to test run the drill press. Wearsafetyglasses wheneverstartingor usingmachine.Failure to comply may result in serious personal injury. Keeplooseclothing rolled up and out of the way of machinery and keep hair pulled back. To test run the drill press: 1. Turn the power supply ON at the main panel. 2. With your finger poised on the paddle switch (in case there is a problem), flip the START button ON. The drill press should run smoothly, with little or no vibration or rubbing noises. Investigate and correct for strange or unusual noises before operating the machine further. If you cannot easily locate the source of a potential problem, refer to Troubleshooting on Page 35. If you still can't solve the problem, contac...
Dieses Handbuch ist für folgende Modelle:Bohrmaschinen und Schrauber - G7948 (7.15 mb)