Stimmen - 5, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Delta Dateigröße: 1.96 mb Dateiname: Unterrichtssprache:

12 Y X Fig. 13 Z ASSEMBLING HEADSTOCK TO COLUMN AND BASE To assemble the headstock to the column: 1. Place the drill press head (P) Fig. 9 on the column as far as it will go. NOTE: Be sure the head-locking screws (R) are do not block the drill press head from fully seating on the column. To reduce the risk of injury, always use at least two people when lifting. 2. Align the head (P) Fig. 10 with the table (Q) and the base (B). 3. Tighten the two head-locking screws (R) Fig. 9 with the 5 mm hex wrench supplied. INSTALLING THE CHUCK To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury. IMPORTANT: Make certain that the tapered hole in the bottom of spindle (U) Fig. 11, and the taper on the spindle adapter (V) are clean and free of grease, lacquer or rust- preventive coatings. NOTE: Remove the rust-preventative oil from the chuck using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol. Push the spindle adapter (V) Fig. 11 into the spindle (U). making certain that the tang (W) engages the mating slot inside the spindle (U). NOTICE RISK OF PROPERTY DAMAGE. To avoid damage to the laser, prevent the cleaning solution from coming in contact with the laser pod. You can clean the laser pod with a dry cotton cloth. IMPORTANT: Make certain the spindle taper (X) Fig. 12, and tapered hole in chuck (Y) are clean and free of any grease, lacquer or rust preventive coatings. NOTE: Remove the rust-preventative oil from the chuck using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol. IMPORTANT: Rotate the chuck until the chuck jaws are fully retracted inside the chuck. Hold the chuck on the taper of the spindle. Tap it with a soft-tip hammer (Z) Fig. 13 or a block of wood and hammer to set the chuck. NOTICE RISK OF PROPERTY DAMAGE. To avoid damage to the chuck, NEVER drive the chuck on the spindle with a metal hammer. Fig. 11 U V W P Fig. 9 R P Fig. 10 Q B 10 ATTACHING THE PINION SHAFT HANDLES To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury. Thread the three pinion shaft handles (AA) in the three holes located in the pinion shaft hub (BB) Fig. 14. ATTACHING THE LED WORK LIGHT To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury. The included LED work light is to be attached to the side of the headstock at wire (CC) Fig. 15. NOTE: Prior to connection, be careful not to push wire (CC) into headstock as it is difficult to retrieve. 1. Remove three 6 mm screws (one shown at DD) Fig. 15. 2. Connect the two wires — (CC) from the headstock and (EE) from the LED worklight — as shown in Fig. 16. 3. Remove plastic cable tie. 4. Push excess wire into the headstock. 5. Attach the LED work light (FF) Fig. 17 to the headstock using three screws removed earlier. One is shown at (DD). 6. Final assembly of LED worklight (FF) looks like Figure 18. CHUCK KEY STORAGE Storage for your included chuck key (GG) is built into the right side of the drill press head stock. Press chuck key into the holder as shown in Figure 19. T-SLOTS The drill press table is fitted with two T-slots (HH) Fig. 20 for use with various drill press accessories (stop blocks, fences, or clamps). Use 5/16" T-bolts or 1/4-20 hex head bolts when attaching your accessory to the table. Fig. 19 HH Fig. 20 FF DD AA AA Fig. 14 Fig. 15 CC CC Fig. 16 Fig. 17 EE Fig. 18 FF GG BB DD Since accessories other than those offered by DELTA have not been tested with this product, use of such accessories could be hazardous. For safest operation, only DELTA recommended accessories should be used with this product. 11 TABLE LOCKING WRENCH STORAGE The table locking wrench can be stored underneath the table as shown in Fig. 21. BELT TENSION LEVER HANDLE To attach the belt tension lever handle (II) Fig. 22, place it in hole (JJ) with the hole (AA) up, as shown. Align set screw (BB) with hole (AA) Fig. 22 and tighten screw down into hole firmly with included hex wrench as shown in Fig. 23. Place M6 x 1 locknut (LL) Fig. 23 on set screw (BB). Firmly tighten locknut (LL) with a 10 mm wrench. II JJ AA BB Fig. 22 TABLE INSERT The drill press table comes with an insert (XX) Fig. 23B made of MDF to help prevent wear and tear on the bit when it drills down through the workpiece. Over time, it will become necessary to replace this piece. It can be made from 3/4" thick MDF cut into a 3-3/4" square. To replace the old insert : 1. Remove two screws from holes (YY) Fig. 23A that hold insert in place. 2. Remove old insert and place your new insert into the table (Fig. 23B). 3. If the insert is not leve...

Herunterladen

Geben Sie zwei Ziffern: