Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Global Machinery Company Dateigröße: 1.78 mb Dateiname: Unterrichtssprache:

This is important. Failure to observe this safety rule could cause serious damage to the battery pack. • Do not incinerate the battery pack even if it is seriously damaged or can no longer hold a charge. The battery pack can explode in a fire. • Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks open or cracks, immediately discontinue its use and do not recharge it. • The battery pack utilizes nickel-cadmium cells. Cadmium is considered to be a toxic material. Use an environmentally safe disposal unit at a municipal waste disposal centre to dispose of a damaged or worn out battery. Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. 8 Know your product This drill can be used for drilling in wood, metal, masonry and screwdriving. Use the tool and accessories only for intended applications. All other applications are expressly ruled out. 1. Single sleeve keyless chuck 2. Torque adjustment/ hammer selection collar 3. Trigger with variable speed control 4. Forward/reverse control (not shown) 5. Adjustable side handle 6. Battery pack release buttons 7. Rechargeable battery pack 8. Charger 9. 3 Speed gear selector 10. Screw Driver bit storage 11. Spirit level 12. Battery indicator button 13. LED Light switch 14. LED lights (x5) 2 9 11 3 8 7 14 1 5 10 6 13 12 4 Know your product This drill can be used for drilling in wood, metal, masonry and screwdriving. Use the tool and accessories only for intended applications. All other applications are expressly ruled out. 1. Single sleeve keyless chuck 2. Torque adjustment/ hammer selection collar 3. Trigger with variable speed control 4. Forward/reverse control (not shown) 5. Adjustable side handle 6. Battery pack release buttons 7. Rechargeable battery pack 8. Charger 9. 3 Speed gear selector 10. Screw Driver bit storage 11. Spirit level 12. Battery indicator button 13. LED Light switch 14. LED lights (x5) 2 9 11 3 8 7 14 1 5 10 6 13 12 4 9 Adjustable side handle The drill is supplied with a 360. adjustable side handle (5). Always fit and use the side handle when using the drill, this increases safety when operating the drill. To adjust the side handle, rotate the side handle in an anti clockwise direction approximately 2 full turns. Once the side handle is loose rotate the collar left or right to the desired position. You do not need to fully remove the handle. If you want to remove the side handle, slide the collar completely forward over the chuck. To tighten the collar on the housing, rotate the handle in a clockwise direction firmly. Ensure the collar is fully located on the aluminium housing. Inserting and removing bits The drill is fitted with auto spindle lock which means if you try and rotate the chuck by hand the spindle of the drill will automatically lock. This means you only need to grasp the chuck and rotate the chuck housing to remove or fit accessories. This drill has a keyless chuck, hence a chuck key is not needed to secure a bit in the drill. Always set the forward/ reverse control (4) to the locked ‘OFF’ position when installing and removing bits. It is also recommended to remove the battery pack to avoid unintentional starting. 1. Open the chuck jaws by firmly holding the chuck housing and rotating the housing in an anti clockwise direction. Open the jaws sufficiently so as to fit the desired accessory. 2. Ensure the accessory is fully inserted. 3. To firmly clamp the accessory in the chuck, grasp the chuck housing and rotate the chuck housing in a clockwise direction. Ensure the bit is retained firmly or damage to the chuck jaws can result. 4. To remove the accessory, open the chuck jaws by firmly holding the chuck housing and rotating the housing in an anti clockwise direction. Open the jaws sufficiently so as to remove the specific accessory. Fitting and removing the battery pack To remove the battery pack from the drill firmly press the battery release buttons (6) at either side of the battery pack, and slide the battery backward out of the tool. To install the battery pack, align rails, on the tool with the tabs on the battery pack and slide the battery pack on to the drill. Ensure the battery pack is sitting straight on the foot and correctly entering the runners. The battery should slide fully on to the drill foot until the battery pack “clicks” into position. 10 Battery charging cb a d e Make sure power circuit voltage is the same as that shown on the charger specification plate. Connect charger to power source. The yellow light (a), should light up. This indicates the charger is ready to begin charging. To remove the battery pack from the charger depress the battery pack release buttons (6). Depending on room temperature, line voltage, and...

Herunterladen

Geben Sie zwei Ziffern: