Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Global Machinery Company Dateigröße: 1.78 mb Dateiname: 7717954b-f44d-c144-a52a-10c55dbe9768.pdf Unterrichtssprache:

Position battery pack on charger; align rails (d), on battery charger with (e) on battery pack. Slide battery forward onto charger until it clicks into position. The red light (b), should begin to glow continuously, indicating that the battery pack is receiving a “Fast Charge”. Note. If the red light does not glow continuously, but the yellow light is flashing and the green light (c), begins to glow, remove battery and re-insert when battery temperature is between 0°C and 40°C. After approximately one hour, the “Fast Charge” indicator red light (b) should go out indicating that the battery pack is fully charged and that the charger is now in a “Maintenance Charge” mode, this is confirmed by the green light (c) coming on. The battery pack can be left on “Maintenance Charge” until you are ready to use it. Battery indicator Press the battery indicator button (12), this will display the level of charge remaining in the battery. The LED’s lighting up indicate the charge remaining in the battery, the higher the number of LED’s the more charge remaining in the battery. When the battery indicator is showing only one LED the battery should be removed and put on the charger. 11 LED Work area light The drill has five LED lights (14) to illuminate the work area and improve vision when drilling in areas with insufficient light. To turn the LED lights on depress the LED light switch (13). To turn the LED lights off repress the LED light switch (13). Trigger Switch To start the drill, depress the trigger switch. Use the forward/reverse control (4) to select the direction of rotation, then squeeze the trigger switch (3). This trigger switch is an electronic variable speed control which enables the user to vary the speed continuously. The speed varies according to how far the trigger switch is depressed, the further it is depressed the faster the chuck will rotate and the lighter it is depressed, the slower it will rotate. The switch is equipped with a brake, the chuck will stop as soon as the trigger switch is fully released. To stop the drill, release the trigger switch. Forward/Reverse control The forward/reverse control (4) allows you to change the direction of the tool while the variable speed trigger is not depressed. To select forward rotation depress the control (4) toward the left side of the tool. To select reverse depress the control (4) to the right side of the tool. Drilling uses the forward mode. The reverse mode is intended for the removal of screws. The centre position of the control button locks the tool in the off position. Variable speed The variable speed feature is particularly useful when driving screws. It also enables you to select the best speed for a particular application. The farther you squeeze the trigger, the faster the tool will operate. Use lower speeds for starting holes without a centre punch, drilling metals or plastic, driving screws and drilling ceramics, or in any application requiring high torque. Higher speeds are better drilling in wood, wood compositions and for using abrasive and polishing accessories. For maximum tool life, use variable speed only for starting holes or fasteners. Note. It is best to use the variable speed feature for a short time only. Do not continuously operate the drill in variable speed mode this may damage the switch. Drilling Positions This symbol indicates the DRILL POSITION. Use this mode for high speed drilling (Wood, Aluminium, and Steel) and the clutch will be locked. This symbol indicates the HAMMER POSITION. Use this mode to select hammer action. For best results in hammer mode, use set the gear selector (9) to Position 3 (high speed). 12 Torque adjustment/hammer selection collar Screw driver bit storage By rotating the torque adjustment/hammer selection collar (2) behind the chuck, it is possible to adjust the torque to each of twenty settings, or select hammer action or the drill setting. The range of twenty torque settings allows better control when using the drill as a screwdriver as it prevents overtightening of the screws. The numbers circling the collar are used to indicate the level of torque. The higher number on the collar, the higher torque and the larger the fastener which can be driven. To select any of the numbers, rotate the collar (2) until the desired number aligns with the arrow head indicator on the housing. 3 Speed gearbox The 3 Speed Gearbox allows you to select a gear with the optimum speed and torque to suit the application. To select the first gear (low speed, high torque setting), turn the tool off and wait until it stops. Push the gear selector (9) back, away from the chuck, so the number 1 is displayed. To select the second gear (medium speed, medium torque setting), turn the tool off and wait till it stops. Slide the gear selector forward towards the chuck, so the number 2 is displayed. To select the third gear (high speed, low torque setting), turn the tool off and wait until it stops. Slide the gear selector (9) to the m...

Herunterladen

Geben Sie zwei Ziffern: