Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Black & Decker Dateigröße: 278.45 kb Dateiname: Unterrichtssprache:

The battery will snap into place. To remove the battery pack, press the release buttons and firmly pull the battery pack of the tool handle. QUICK RELEASE CHUCK NOTE: The chuck accepts 1/4" hex accessories only. To install an accessory, pull the chuck collar toward the front of the tool, insert the accessory, and release the collar (Figure 1) . The accessory will lock into place. To remove an accessory, pull the chuck collar toward the front of the tool. Remove the accessory and release the collar. FORWARD/REVERSE BAR For forward operation, push the bar from right to left. For reverse operation, push the bar FIG. 1 3 DW900,5/8/2:59 Page 4 English from left to right. the tool. Be sure to release the FIG. 2 forward/reverse bar. SWITCH To turn the tool on, squeeze the its set torque level, the spindle of the tool will illuminate. Do not continually trigger when driving a joint; let the tool Adjusting Torque Level WARNING: Remove the battery before making any adjustments. 1) Insert a 1/4" hex key into the spindle and turn it You may hear a click, indicating the clutch is coupled. ADJUST 2) Insert the wireform tool into the two holes on the front WINDOWTOOL unit. Be sure to insert the wireform tool as shown in Figure Slowly turn the ring until the symbol shows through the window on the top front of the tool. At this point, the wireform will drop into two adjustment notches under the front ring. You FIG. 5 will not be able to rotate the ring after the wireform tool drops into the notches. 3) Remove the wireform tool from the front of the unit, and re-insert it as shown in Figure 3. NOTE: Remove wireform tool before operating unit. 4) Insert a 1/4" hex key into the spindle. Holding the unit and wireform tool in one hand, turn the hex key with the other hand (Figure 4). Turn the key counterclockwise to decrease the torque, clockwise to increase the torque. The spindle will click at each torque setting. Each click signifies a torque change of approximately 0.08 N-m. NOTE: If the spindle stops clicking and you feel significant resistance, the tool is at its torque limit. Do not force the tool beyond this point. 5) Remove wireform tool. Check the torque of the tool with a torque 4 FIG. 3 FIG. 4 DECREASE TORQUE OPTIONAL BALE HANDLE INCREASE TORQUE DW900,5/8/2:59 Page 5 meter. If necessary, readjust the torque SETTING FOR above instructions. in-lbs This tool can achieve a 4.5 N-m and a minimum torque of Setting the Indicator Once the desired torque is confirmed use the wireform tool to set the indicator ring. 1/4" into the holes on the front ring and numbers on the ring match the torque setting meter (Figure 5). Setting the indicator ring will also seal the adjustment holes and prevent dirt from getting FIG. 6 FIG. 7 NOTE: Adjusting the indicator ring does not change the torque setting of the tool. Replacing the Motor Cartridge WARNING: Remove the battery before performing any service. NOTE: To avoid damage to the electronic module, this operation must be performed while wearing a grounding strap attached to earth ground. 1) Remove the four fasteners on the back of the tool; remove the endcap. 2) Remove the rubber O-ring from the motor (Figure 6). 3) Using pliers, remove the motor leadwires, noting color codingALIGN GROOVES TO and connection scheme (Figure 6). GUIDE MOTOR INTO HOUSING 4) Grasp the motor and pull it out from the rear of the unit. Discard the motor. 5) Install the O-ring on the replacement motor. 6) Align the replacement motor with the housing (Figure 7). The groove formed by the sheet metal ring over the motor should align with the ribs located on the interior of the left housing (as 5 Nmin-lbs2.8in-lbsNm30SETTING FOR N-m FIG. 5A O-RING RED LEADWIRELED BLACKLEADWIRE English DW900,5/8/2:59 Page 6 English viewed from the FIG. 8 7) While holding the tool up, allow the motor to 8) Insert the 1/4" hex wrench spindle, and turn the spindle gear teeth on the motor engage gears in the tool. The motor will drop about 1/4" into the tool housing (Figure 8). 9) Inspect all leads for damage; repair or replace as required. 10) Reattach motor leadwires, routing wires around the motor can. The wires should be routed down and inward near the LED. Ensure the wires are not blocking the LED. 11) Replace the endcap, tighten the four fasteners to 0.9 N-m head torque. Operation Tips • Pulling the trigger once uses about the same amount of battery power as driving one fastener. Avoid running the tool at “no-load” to conserve battery power. • Avoid “feathering” the trigger. Allow the tool to stop automatically when driving a fastener. Accessories Recommended accessories for use with your tool are available at extra cost from your distributor or local service center. CAUTION: The use of any non-recommended accessory may be hazardous. BATTERY PACKS DW9072 12.0V 4/5 Cell, Standard DW9074 12.0V 4/5 Cell, Standard Charge Indicator DW9070 12.0V High Capacity XR™ Pack CHARGERS DW9106 1 Hour Charger DW9115 15-Minute Charger DW9107 XR2 Ch...

Herunterladen

Geben Sie zwei Ziffern: