Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Makita Dateigröße: 95.66 kb Dateiname: Unterrichtssprache:

54-06-2800 SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS REVISED BULLETIN DATE Jan. 2003 1/4 INCH DRILL CATALOG NO. 0100-20 STARTING SERIAL NO. 058A WIRING INSTRUCTION 58-01-1805 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). FIG. PART NO. DESCRIPTION OF PART 1 02-04-0640 Ball Bearing 2 02-04-0645 Ball Bearing 3 02-04-0852 Ball Bearing 4 02-04-1229 Ball Bearing 5 02-50-1611 Needle Bearing 6 02-50-2400 Needle Bearing 7 06-82-7275 7-18 x 3/4 Slotted Plastite T-20 8 12-99-2565 Service Nameplate 9 16-10-2215 Armature 10 18-07-2200 Field 11 22-18-1210 Brush Card Assembly 12 22-56-1010 Pin Housing Assembly 13 48-76-4008 Quik-Lok Cord Set 14 23-66-2585 Switch 15 28-14-2390 Gearcase 16 28-28-2320 Diaphragm 17 31-15-2030 Handle Halve 18 31-50-2040 Motor Housing 19 32-40-0100 Intermediate Gear 20 32-75-0115 Spindle Gear 21 34-80-2300 Retaining Ring 22 36-66-0125 Intermediate Shaft 23 38-50-5750 Spindle 24 42-14-0460 Baffle Assembly 25 43-44-0985 Gasket 26 44-60-1700 Ground Pin 27 45-04-0750 Chuck Screw 29 45-36-1095 Spindle Spacer 30 45-88-7990 Thrust Washer NO. REQ. FIG. PART NO. DESCRIPTION OF PART NO. REQ. 31 49-15-0265 Side Handle Assembly (1) 32 48-66-0070 1/4 Chuck (1) 33 48-66-3200 Chuck Key (1) 34 48-66-4080 Chuck Key Holder (1) 35 22-84-0845 Fan (1) 36 45-30-0030 Slug (2) 37 45-30-0035 Slug (1) 38 23-52-1610 Brush Spring (2) 39 22-18-1310 Brush Assembly (2) 40 06-75-2850 3/8-16 x 5-1/2 Hex Cap screw (1) 41 42-68-0800 Side Handle Clamp (1) 42 43-62-0845 Side Handle (1) 43 06-54-0325 3/8-16 Square Nut (1) LUBRICATION (Type "Y" Grease, No. 49-08-5270) • Place 5 gm. (.02 oz.) of grease on top of the inserted intermediate ball bearing (1) and on the intermediate pinion (22). • After inserting all gearing, place 13 gm. (.46 oz.) of grease at the armature pinion location in the gearcase (15) and fill to the top of the intermediate gear (19). Grease must contact at least 25% of the intermediate gear teeth. Before assembly, lightly coat all press fit areas with lightweight spindle oil. FIG. 4,20 5,6 NOTES: Support the output ball bearing inside the gearcase before pressing off the spindle gear. Needle bearings to be pressed flush to .010 under flush from the end which has the vendors identification. MILWAUKEE ELECTRIC TOOL CORPORATION 13135 W. LISBON RD., BROOKFIELD, WI 53005 D...

Herunterladen

Geben Sie zwei Ziffern: