Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Harbor Freight Tools, modell BTP130

Hersteller: Harbor Freight Tools
Dateigröße: 1.07 mb
Dateiname: 0468dddd-fe04-4c87-aff6-3ddabc4e6dc7.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

• Always set the lever correctly to your desired mode mark. If you operate the tool with the lever positioned halfway between the mode marks, the tool may be damaged. Adjusting the fastening torque (Only for screwdriving operation mode “ ”) The fastening torque can be adjusted in 16 steps by turning the adjusting ring so that its graduations are aligned with the pointer on the tool body. The fastening torque is minimum when the number 1 is aligned with the pointer, and maximum when the number 16 is aligned with the pointer. The clutch will slip at various torque levels when set at the number 1 to 16. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application. NOTE: • In modes other than screwdriving mode, the adjusting ring can be placed at any position because it does not work. 1. Action mode changing lever 1. Action mode changing lever 1. Action mode changing lever 1. Action mode changing lever 1 007158 1 007159 1 007160 1 007161 1. Action mode changing lever 1. Adjusting ring 2. Graduation 3. Pointer 1 007162 1 2 3 007163 2 1 2 1 CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit or socket bit 004521 Use only the driver bit or socket bit shown in the figure. Do not use any other driver bit or socket bit. For European and North & South American countries, Australia and New Zealand 006348 Use only these type of bit. Follow the procedure (1). A=12mm B=9mm (Note) Bit-piece is not necessary. For other countries 006349 To install these types of bits, follow A=17mm the procedure (1). B=14mm (Note) Makita bits are these types. To install these types of bits, follow A=12mm the procedure (2). B=9mm (Note) Bit-piece is necessary for installing the bit. 1. To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. 001267 1 2 1. Bit 2. Sleeve 2. To install the bit, pull the sleeve in the direction of the arrow and insert the bit-piece and bit into the sleeve as far as it will go. The bit-piece should be inserted into the sleeve with its pointed end facing in. Then release the sleeve to secure the bit. 004347 1. Bit 2. Bit-piece 3. Sleeve 1 2 3 To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly. NOTE: • If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not be secured. In this case, try re-inserting the bit according to the instructions above. Hook (Accessory) 006251 1. Hook 2. Screw 3 3. Groove CAUTION: • When installing the hook, tighten the screw firmly. Failure to do so may cause the breakage of the tool or personal injury. The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out. OPERATION CAUTION: • Always insert the battery cartridge all the way until it locks in place. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. 7 Impact driver operation Impact driver operation mark. The adjusting ring can be placed at any position. Screwdriving Hold the tool firmly and place the point of the driver bit in the screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation. 007411 007319 High tensile bolt 0 120 100 80 60 40 20 N m Fastening torque Fastening time S) Proper fastening torque (ft lbs) (87) (72) (58) (43) (29) (14) ( M12(1/2") M10(3/8") (M12) M8(5/16") (M10) (M8) (1/2") (3/8") (5/16") 0 1.0 2.0 3.0 Tightening bolts The proper fastening torque may differ depending upon the kind or size of the screw/bolt, the material of the workpiece to be fastened, etc. The relation between fastening torque and fastening time is shown in the figures. 007317 120 100 80 60 40 20 Standard bolt N m Fastening torque Fastening time S) Proper fastening torque (ft lbs) (87) (72) (58) (43) (29) (14) ( 0 1.0 2.0 3.0 M14(9/16") M12(1/2") (M14) M10(3/8") (M12) M8(5/16") (M10) (M8) 0 (9/16") (1/2") (3/8") (5/16") NOTE: • Use the proper bit for the head of the screw/bolt that you wish to use. • When fastening screw M8 or smaller, carefully adjust pressure on the switch trigger so that the screw is not damaged. • Hold the tool pointed straight at the screw. • If you tighten the screw for a time longer than shown in the figures, the screw or the point of the driver bit may be overstressed, stripped, damaged, etc. Before starting yo...