Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
While holding the Chuck Sleeve in place, turn the Chuck clockwise to lock the bit in place. The Chuck (1) accepts up to 3/8” diameter bits. Insert the appropriate bit for your application and tighten the Chuck (1) firmly. (See Figure E, above.) Secure the workpiece in place, using a vise or clamps (not included). The Torque Setting Ring (3) allows you to select 20 different driving torque settings, depending on the job required. Torque Settings (1-20): The different numbers on the Ring are an indication of how much torque the screwdriver will apply to the bit before the clutch slips, allowing the bit to stop and helping to prevent damage to the screw, bit, or workpiece. The higher the number, the more torque is applied before the clutch slips. Unless you are drilling, always start with a lower number to help prevent damage. BATTERY BUTTON LOCK (26) Drill Setting (): This setting essentially prevents the clutch from slipping entirely. It is designed for drilling, but is not advised for using the screwdriver because it offers no protection against stripping the head or splitting the wood. Set the driving torque by turning the Torque Setting Ring (3) to align the torque indicator arrow with the desired setting. (See Figure E, previous page.) When drilling in light gauge metal or wood, use a wooden block to back up the material to prevent damage to the workpiece. Mark the center of the hole to be drilled with a center punch to give a Drill Bit a start and to prevent it from “walking”. Lubricate the Drill Bit with cutting oil when drilling iron or steel. Use a coolant when drilling nonferrous metals such as copper, brass, or aluminum. Insert the fully charged Battery Pack (23) into the Handle of the Cordless Drill. The Locking Lever (7) allows you to change the rotational direction of the Cordless Drill. For a clockwise rotation, move the Locking Lever to the right. For a counterclockwise rotation, move the Steering Stem to the left. The center position locks the Trigger (10), helping to prevent the Drill from operating. (See Figure E.) Make sure to hold the Cordless Drill firmly with both hands, as torque from the Motor will cause the tool to twist. Operate the Drill, by squeezing the Trigger (10). The speed of the Drill can be controlled by varying the pressure on the Trigger (10). If Drilling: • Use the Drill torque setting, as described above. • Drill only as deep as necessary. Do not drill deeper than necessary into walls or other areas where you cannot identify any possible hazards behind the drilling surface. • To reduce jamming as the Bit breaks through the workpiece, decrease the drilling pressure when the point of the Bit breaks through the workpiece. • When you have drilled the hole, remove the Bit from the hole while the Cordless Drill is still running. This prevents the Bit from getting caught in the hole and causing damage. If Driving Screws: • Start with a low torque setting. • If the clutch starts slipping before the screw is in all the way, stop the drill, put the Locking Lever (7) in the center position, remove the Battery (23), and change the torque setting. Reinstall the Battery (23), and set the direction before continuing. Release the Trigger (10) to stop the Drill. Then, remove the Battery Pack (23), put the Locking Lever (7) in the center position, and remove the bit from the Drill. INSPECTION, MAINTENANCE, AND CLEANING WARNING! Remove the Battery (23) from the tool and set the Locking Lever (26) to its center, locked position before performing any inspection, maintenance, or cleaning. BEFORE EACH USE, inspect the general condition of the Cordless Drill. Check for misalignment or binding of moving parts, cracked or broken parts, leaking Battery Pack, damaged Charger wiring, chipped or broken Drill Bits, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. DAILY: With a soft brush or cloth, remove all dirt and debris from the Cordless Drill. Do not immerse the Cordless Drill in any liquids. If the battery needs replacement keep in mind that the Nickel-Cadmium (Ni- Cd) battery in this tool must be recycled or disposed of properly. PARTS LIST Part Description Q’ty 1 Chuck 1 2 Plate 1 3 Torque Setting Ring 1 4 Radiator 1 5 Upper Orientation Block 1 6 Lower Orientation Block 1 7 Locking Lever 1 8 Orienting Plate 1 9 Spring 1 10 Trigger 1 11 Bushing 1 12 Steel Ball 13 Battery Terminal Clamp 1 14 Gear Housing 1 15 Left Housing 1 16 Motor Support 1 17 Screw 18 Drive Gear 1 19 Motor 1 20 Right Housing 1 21 Charger 1 22 AC/DC Adapter 1 23 Battery Pack 1 Part Description Q’ty 24 Terminal 2 25 Terminal Mount 1 26 Battery Button Lock 2 27 Battery Cell 12 28 Battery Lower Housing 1 29 Screw 30 Battery Button Spring 2 31 Ribbed Block 1 32 Chuck Screw 1 33 Screw 3 34 Washer 1 35 Clip 1 36 Washer 1 37 Washer 1 38 Steel Ball 39 Gear Cage 1 40 Planetary Gear 3 41 Outer Gear 1 42 Sun Gea...