Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
• Do not heat batteries, disassemble them, or throw them into flames or water. English •Batteries may have different voltages, even if they are the same size and shape. Do not use different types of batteries together. •To prevent leakage of battery fluid, remove the batteries if you do not plan to use the remote control for a long period of time (1 month or more). If the fluid should leak, wipe it carefully off the inside of the case, then insert new batteries. If a battery should leak and the fluid should get on your skin, flush it off with large quantities of water. • When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/area. • WARNING Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries. Using the remote control The remote has a range of about 7 m at an angle of about 30. from the remote sensor. Keep in mind the following when using the remote control: •Make sure that there are no obstacles between the remote and the remote sensor on the unit. • Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the unit’s remote sensor. • Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit. •Replace the batteries when you notice a fall off in the operating range of the remote. En Connections Connections Chapter 2: Connections •Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections. • Connect the power cord after all the connections between devices have been completed. Connecting using a video cable • When an iPod/iPhone is connected to this unit, the TV output setting of iPod/iPhone is automatically set to ‘ON’.1 • Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the television. This unit’s rear panel ANTENNA VIDEO OUT DC IN 19 V FM75 TV Video cable (supplied) To video input terminals Yellow Connecting using an HDMI cable By using an HDMI cable, digital signals can be transferred to an HDMI-compatible TV on a single cable with no loss of picture or sound quality.2 After connecting, adjust unit resolution and HDMI color settings according to the HDMI- compatible TV. Also refer to the operating instructions with the HDMI-compatible TV. HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries. Connecting to a TV This unit’s rear panel AS-BT200 • If you connect this unit to yourtelevision with the HDMI cable, sound can not be transferred from your television to this unit. To listen to sound, connect the rearpanel AUX IN mini-plug jack to your television. ANTENNA LABEL SIDE VIDEO OUT DC IN 19 V FM75 HDMI OUT Match the direction of the plug to the terminal and insert straight. To HDMI input terminal HDMI cable (commercially available) TV Note 1 • Some iPod allow the TV output setting to be changed while connected. • When the iPod/iPhone is disconnected from this unit, the iPod/iPhone’s TV output setting returns to its original state. 2• When playing a disc or USB storage device content, this unit can transfer digital signals by the HDMI OUT terminal. Use the video cable for playing other content. • This unit’s interface is designed based on the High-Definition Multimedia Interface specification. • When an HDMI-compatible device is connected, the resolution is displayed on the front panel display. • The resolution of video signals output from this unit’s HDMI OUT terminal is changed manually. Change the HDMI Resolution setting (page 26). Settings for two units can be stored in memory. • This unit is designed for connection to HDMI-compatible devices. It may not operate properly if connected to DVI devices. En Connections Connections 02 Connecting to an AV receiver or amplifier This unit’s rear panel AS-BT200 ANTENNA LABEL SIDE VIDEO OUT DC IN 19 V FM75 HDMI OUT Match the direction of the plug to the terminal and insert straight. To HDMI input terminal HDMI cable (commercially available) TV To HDMI input terminal From HDMI output terminal AV receiver oramplifierHDMI cable (commercially available) Audio signals that can be output from this unit's HDMI OUT terminal • 44.1 kHz to 96 kHz, 16-bit/ 20-bit/ 24-bit 2-channel linear PCM audio (including 2-channel downmixing) • Dolby Digital 5.1-channel audio • DTS 5.1-channel audio • MPEG audio • Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Connecting the FM antenna Connect the FM antenna plug onto the center pin of the FM antenna ...
Dieses Handbuch ist für folgende Modelle:Heimkino-Systeme - X-SMC1-S (24.73 mb)
Heimkino-Systeme - X-SMC1-W (24.73 mb)