Stimmen - 5, Durchschnittliche Bewertung: 3.6
(
)
)
|
Fotos und technische Daten Yamaha DVX-S120 |
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Once DTS audio finishes playback, the tindicator may blink, and while it blinks only DTS audio can be played back. Immediately after DTS audio finishes playback, if you want to play normal PCM audio, reset the Input mode to AUTO. — If the DTS signal is interrupted when you perform Search or Skip, the tindicator may blink. If this condition continues for over 30 seconds, the Input mode automatically changes from DTS to normal digital (PCM) and the tgoes out. • Using “* Input Mode” in the SET MENU you can set whether to use the Input mode specified previously when CinemaStation was turned on or return to AUTO. • It is not possible to select ANLG with the DVD/CD Input Selection button. • You cannot switch input modes when the input jack you select with the Input Selection button can only input an analog input signal. • To play back DTS, set the Input mode to AUTO or DTS. Do not set it to ANLG. If you do, audio may not output or you may hear noise. Advice Note English TV CH CINEMA CH POWER POWER AUDIO /DTS SELECT NIGHT SW TV CH TV INPUT SLEEP PRESET PRESET A B C D E CENTER SURR SHIFT STEREOMATRIX 6.1 A-BREPEAT ANGLE SUBTITLE DVR-S120 WB56650 ON SCREEN MENU TEST RETURNSTATUS TV VOL VOLUME MUTE AMP DVD/CD VCR VIDEO TUNER MOVIE MUSIC SPORTS GAME SET MENU ENTER You can playback most sources without a problem with the AUTO setting (factory default setting). Then depending on your needs, you can select the priority level for digital and analog input signals, and specify formats such as DTS. Press the Input Selection button for current input source until the desired input mode appears in the CinemaStation Display. AUTO: Input signal can be selected in the order below. 1) Digital signal 2) Analog signal DTS: Only DTS can be played. ANLG: Only analog signal can be played. Learning about input modes, jacks and Input Selection buttons CinemaStation can receive signals from the VIDEO (analog), VCR (analog) and OPTICAL (digital) jacks of equipment that is connected to it. You can assign a VIDEO or VCR input name to the OPTICAL IN jack. This will allow you to use the VIDEO button or VCR button to input a device connected to the Input OPTICAL IN jack (VIDEO is assigned in the default setting.) Selection buttons Normally, an analog signal is input to the VIDEO or VCR IN jack, and a digital signal is input to the OPTICAL IN jack. However, by setting the input mode to AUTO the input will be automatically detected and you can then playback audio from the device you want by simply pressing an Input Selection button. Additional Features Additional Features After a specified time the power automatically enters standby so you can enjoy CinemaStation until you fall asleep. Play the source. TV CH CINEMA CH POWER POWER AUDIO /DTS SELECT NIGHT SW TV CH TV INPUT SLEEP PRESET PRESET A B C D E CENTER SURR SHIFT STEREOMATRIX 6.1 A-BREPEAT ANGLE SUBTITLE DVR-S120 WB56650 ON SCREEN MENU TEST RETURNSTATUS TV VOL VOLUME MUTE AMP DVD/CD VCR VIDEO TUNER MOVIE MUSIC SPORTS GAME SET MENU ENTER Repeatedly press SLEEP and set the time to enter standby mode. The CinemaStation Display changes as shown below. SLEEP 120 min SLEEP SLEEP 90 min SLEEP 60 min SLEEP 30 min SLEEP OFF Once the Sleep Timer is set a SLEEP indicator lights up in the CinemaStation Display. To cancel the Sleep Timer Keep pressing SLEEP until SLEEP OFF appears in the CinemaStation Display. In a few seconds SLEEP OFF disappears. The CinemaStation Display once again shows the DSP Program and the SLEEP indicator disappears. • You cannot link the sleep timer of the device that is playing, so make sure to set the sleep timer of each device separately. • The Sleep Timer cancels if you press POWER on the Remote Control, press STANDBY/ON on CinemaStation or pull out the power cord. • Memory backup remembers the previous setting so you can use the same setting next time. Advice Additional Features Additional Features Progressive Scan (NTSC only) The COMPONENT VIDEO jack on CinemaStation is compatible with Progressive Scan.You can enjoy highly defined images without flicker when connecting to a television that has a component video input jack compatible with Progressive Scan. Progressive Scan is available only for NTSC signal output. See pages 94 and 95, “On Screen Menu Guide”. Please... • Before connecting make sure to turn off the television and CinemaStation power. Connect the television. Use a commercially available component video cable. Start playing the DVD. See page 10, “Viewing a DVD”. Press PROGRESSIVE on CinemaStation. DIGITAL AUDIO VIDEOS VIDEO INVCR OUT Y PB PR MONITOR OUT MONITOR OUT (DVD ONLY) MONITOR OUT (DVD ONLY) VCR IN VIDEO INCOMPONENT VIDEO OUT OPTICAL Y PB PR PROGRESSIVE The PROGRESSIVE indicator lights up. To cancel Progressive Scan Press PROGRESSIVE to turn off the PROGRESSIVE indicator. • If you play video with a 4:3 aspect ratio on a 16:9 wide television screen, Progressive Scan may fill the screen top to bottom. In this case, use the On Screen Menu to change to the sc...