Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
(The indicator will turn off in 1 second.) 2 With the wireless receiver module turned on, use a ball point pen or a pair of tweezers to press the RESET button on the back of the unit. . The Standby/On LED on the front panel of the wireless receiver module blinks 2 times. 3 Turn on the main unit. WIRELESS RECEIVER MODULE . The Link LED of the wireless receiver module is lit and the setup is finished. . If Power Standby mode continues, repeat Steps 1 to 3 above. Caution . When the wireless receiving module setting is complete, no audio signal is output from the Rear Speaker OUT ports on the back of the main unit. . The wireless receiving antenna is built into the wireless receiver module. Keep the unit away from water and moisture. . For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions. . Sound will be heard from the wireless rear speakers in DVD 5.1-CH or Dolby Pro Logic II mode only. . In 2-CH mode, no sound will be heard from the wireless rear speakers. Note . Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the main unit, some sound interruption may be heard due to interference. . If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, or any other device that uses the same frequency (2.4GHz) near the system, some sound interruption may be heard due to interference. . The transmission distance of radio wave is about 33 feet, but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the main unit and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal. 15 GB Connecting the Video Out to TV Choose one of the three methods for connecting to a TV. CONNECTIONS METHOD 1 METHOD 3METHOD 2 METHOD 1 Composite Video ............... Good Quality Connect the supplied video cable from the VIDEO OUT jack on the back panel of the system to the VIDEO IN jack on your television. METHOD 2 Scart ............... Better Quality If you television is equipped with an SCART input, connect an Scart Jack (not supplied) from the AV OUT jack on the back panel of the system to the SCART IN jack on your television. VIDEO SELECT Function Press and hold VIDEO SEL. button on the remote control for over 5 seconds. . "COMPOSITE" or "RGB" will appear in the display. At this time, press the VIDEO SEL. button shortly to select between "COMPOSITE" and "RGB". . If Scart (RGB Input) is equipped for your TV, press VIDEO SEL. button to select RGB mode. You can get a better picture quality by using Scart setting. . If Scart (RGB Input) is not equipped for your TV, press VIDEO SEL. button to select COMPOSITE mode. METHOD 3 Component (Progressive Scan) Video ............... Best Quality If your television is equipped with Component Video inputs, connect a component video cable (not supplied) from the Pr, Pb and Y jacks on the back panel of the system to the corresponding jacks on your television. Note . When the Progressive scan mode is selected, the VIDEO output (Yellow) and SCART output does not output any signal. 16 P.SCAN(Progressive Scan) Function Unlike regular Interlace Scan, in which two fields of picture information alternate to create the entire picture (odd scan lines, then even scan lines), Progressive Scan uses one field of information (all lines displayed in one pass) to create a clear and detailed picture without visible scan lines. 1 Press STOP button. . If playing a disc, press the STOP button twice so that .STOP., appears on the display. 2 Press and hold P.SCAN button on the remote control for over 5 seconds. . Pressing and holding the button for over 5 seconds will select "Progressive Scan" and "Interlace Scan" alternately. . When you select P.SCAN, "P.SCAN" will appear on the display. . To set P.Scan mode for DivX discs, press the P.SCAN button on the remote control for more than 5 seconds with no disc in the unit (.’NO DISC" on the display), then load the DivX disc and play. What is Progressive (or Non-Interlaced) Scanning? Interlaced Scan (1 FRAME = 2 FIELDS) In interlaced-scan video, a frame consists of two interlaced fields (odd and even), where each field contains every other horizontal line in the frame. The odd field of alternating lines is displayed first, and then the even field is displayed to fill in the alternating gaps left by the odd field to form a single frame. One frame, displayed every 1/30th of a second, contains two interfaced fields, thus a total of 60 fields are displayed every 1/60th of a second. The interlaced scanning method is intended for capturing a still object. Progressive Scan (FULL FRAME) The progressive scanning method scans one full frame of video consecutively down the screen, line by line. An entire image is drawn at one time, as opposed to the interlaced scanning process by which a video image is drawn in a ser...
Dieses Handbuch ist für folgende Modelle:Heimkino-Systeme - HT-Q20 (8.23 mb)
Heimkino-Systeme - HT-TQ22 (8.23 mb)