Login:
heruntergeladen wurde: 4   Dateigröße: 4 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

Connect the dispenser to the power supply. After a .6 second delay the indication must be 4.0 to 24.5 volts dc. AUGER DRIVE COMPONENTS - FMD-4 & FMD-5 P2635 AUGER DRIVE COMPONENTS - FMD-4 (cont.) Auger Drive Motor (Refer to Fig. 2) 1. Remove hopper assy (15), and set aside for reassembly. 2. Remove the four #8-32 screws securing the hopper support plate (11), remove plate and set aside for reassembly. 3. Remove the four #8-32 screws, located inside the dispenser housing on the lower right front

heruntergeladen wurde: 2   Dateigröße: 4 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

Connect the dispenser to the power supply. The indication must be: a) 120 volts ac for two wire 120 volt models. b) 120 volts ac for three wire 120/208 volt or 120/ 240 volt models. 5. Disconnect the dispenser from the power source. If voltage is present as described, proceed to #6. If voltage is not present as described, refer to the wiring diagram and check the dispenser wiring harness. 6. With a voltmeter, check the voltage across the remaining two wires of the dispense switch being tested fr

heruntergeladen wurde: 5   Dateigröße: 4 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

Use at least two people to lift or move the dispenser. 1. Set the dispenser on a sturdy counter top. The dispenser requires a minimum of 6.0” air clearance at the rear of the dispenser. For optimum performance, do not let warm air from surrounding machines blow on the ULTRA dispenser. NOTE – The dispenser should be level or slightly lower in front for proper operation. 6.0” MIN. 2. Remove all shipping material, including the compressor support eyebolt, the cooling drum supports, the “Do Not Lift

heruntergeladen wurde: 0   Dateigröße: 3 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

Minimal clearance is required between the dispenser sides and the wall or another appliance. For optimum performance, do not let warm air from surrounding machines blow on the JDF-2S. Leave some space so the dispenser can be moved for cleaning. ELECTRICAL REQUIREMENTS CAUTION: The dispenser must be disconnected from the power source until specified in Electrical Hook-Up. The 120V rated dispensers have an attached cord set and require a 2-wire, grounded, individual branch circuit rated 120 volts

heruntergeladen wurde: 7   Dateigröße: 3 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

1. Open the Cabinet Door and allow the support arms to lock in place. Door must remain open during the entire cleaning procedure. 3. Twist the Whipper Chamber clockwise and pull it off the Whipper Chamber Receptacle. 4. Pull the Frother off the Motor Shaft. Notice the flat keyway on the shaft and the matching keyway inside the Frother. It is important that these two keyways are lined up when reassembling. 5. Twist Whipper Chamber Receptacle clockwise and pull it off the Motor Shaft. 9. Depress t

heruntergeladen wurde: 26   Dateigröße: 3 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

Door must remain open during the entire cleaning procedure. 2. Place the power switch in the OFF position. Slide the gate shut on the powder hopper and remove the hopper. Wipe the hopper tray clean of powder residue. 4. Twist the Whipper Chamber clockwise and pull it off the Whipper Chamber Receptacle. 3. Pull the Mixing Chamber out of the Whipper Chamber. 6. Twist Whipper Chamber Receptacle clockwise and pull it off the Motor Shaft. Wipe down all inside surfaces. 5. Pull the Frother off the Mot

heruntergeladen wurde: 0   Dateigröße: 3 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

11. Wash the drum(s), hopper drip tray(s), top cover(s), and outer enclosure using a clean wash cloth that has been dampened in the hot water and sanitizer solution. Pay particular attention to the shaft area and make sure it is thoroughly cleaned and sanitized. 12. Thoroughly rinse all surfaces with a clean wash cloth that has been dampened with hot water. Wipe dry with a clean dry wash cloth before reassembling the dispenser. NOTE – Although most parts are dishwasher safe, they may be affected

heruntergeladen wurde: 3   Dateigröße: 2 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

All notices are to be kept in good condition. Replace any unreadable or damaged labels. 41093 040408 CLEANING RECOMMENDED WEEKLY CLEANING: This should be done in conjunction with the recommended weekly cleaning of your machine. The Hoppers must be empty before starting. 1. Prepare a 1 gallon cleaning solution consisting of 1 gallon of hot water and a sanitizing cleaner which contains 3-5% chlorine based sanitizer. Mix per manufacturers instructions 2. Remove connectors from each concentrate cont

heruntergeladen wurde: 1   Dateigröße: 2 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

Two screens will appear for left and right. The operator can scroll through a range of a minimum of1 (ULTRA) to a maximum of 16 (ICE). Factory default is 10. SET THICKNESS ? NO YES MIN LEFT 9 MAX MIN RIGHT 5 MAX 32080 032702 10 Test Augers This function tests the operation of forward and reverse of each auger motor. Left auger appears first. Press the ICE hidden switch to toggle between OFF, FORWARD and REVERSE. Press GOURMET hidden switch to repeat the operation for the right auger motor. A one

heruntergeladen wurde: 11   Dateigröße: 2 mb   Hersteller: Bunn  
Kategorie: Dispenser
@name

(BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA). PLUMBING HOOK-UP 1. Securely attach the short piece of tubing on the water strainer assembly to the inlet fitting on the bottom of the dispenser. 2. Flush the water line and securely attach it to the flare fitting on the water strainer assembly. 3. Turn-on the water supply. 29112 051200 4 INITIAL FILL & HEAT CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, exc





Kategorien