Login:
heruntergeladen wurde: 1   Dateigröße: 3 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

Allow the system to sit for approximately 20 minutes. During this period the system pressure should not rise. If the system pressure rises and stabilizes there is moisture in the system and further evacuation is needed. If the pressure continues to rise check the system for leaks. Ambients Minimum Maximum Air temperature1 10.C/50.F 37.8.C/100.F Water temperature2 4.4.C/40.F 32.2.C/90.F 1Ambient air temperature is measured at the air-cooled condenser coil inlet. 2Ambient water temperature is meas

heruntergeladen wurde: 9   Dateigröße: 2 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

Check dispenser and icemaker operation. 16. Sanitize icemaker according to instructions in icemaker manual. Discard ice made during sanitizing process. 17. Turn off icemaker bin signal switch. 18. Remove dispenser hopper lid; clean and sanitize dispenser according to instructions beginning on page 16. 19. Turn icemaker bin signal switch on and replace front covers, securing with screws. 8 Installing countertop dispensers ! Dispensers with top mount icemakers cannot be mounted on legs.They must b

heruntergeladen wurde: 8   Dateigröße: 2 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

7 and 8) using wall bracket as template. 5. Lift dispenser onto wall bracket, positioning unit so that hook on back of dispenser is captured by wall bracket support angle (Fig. 6, hook detail). ! Do not rest dispenser weight on bottom front edge of wall bracket. 6. Install four 1/4-20 screws through bottom of wall bracket into bottom of dispenser to secure dispenser to bracket. 7. Remove splash panel. Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at e

heruntergeladen wurde: 0   Dateigröße: 1 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

Dispensers and Satellite-fill icemakers are supplied with a 2m (7ft) power cord. Ambient Air temp 38°C/100°F max. 10°C/50°F min. (best performance below 27.C/80°F) Water temp 32°C/90°F max. 4°C/40°F min. (best performance below 21°C/70°F) Water pressure 4.8 bar/70 P.S.I. max. .69 bar/10 P.S.I. min. Plumbing 25/50C with 25/50H with 25/50C with 25/50H with 25/50FB Satellite-fill Satellite-fill integral integral icemaker icemaker icemaker icemaker icemaker in base Dispenser drain1 3/4" FPT 3/4" ID

heruntergeladen wurde: 2   Dateigröße: 1 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

k, male, bin signal, freestanding dispensers Not shown 502945 Cord & plug, male, bin signal, Satellite-fill Not shown 502931 Cord & connector, icemaker power, top mount Not shown 502930 Cord & connector, icemaker power, freestanding Not shown 502805 Caster Not shown 502925 Elbow, water inlet, 10mm (3/8") Not shown 26 Part # Description Reference 502057 Fastener, dispense chute bracket 1 502356 Tube, water station 2 502681 Cover, dispense chute 3 502359 Switch, dispense, ice, lever actuated (incl

heruntergeladen wurde: 0   Dateigröße: 1 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

Note: Do not run condenser supply water through icemaker water filter system. 8. Connect condenser drain line to 19mm (3/4") FPT condenser outlet fitting on back of dispenser (Fig. 1E). Important: Do not connect condenser drain line to any other drain lines. 9. Install appropriate plug on provided cord and insert into wall socket. Refer to wiring diagrams (p.18, 19). 7 Fig. 1 – Rear connections, freestanding models 800mm 384mm 79mm79mm 259mm 267mm 171mm 20mm power cord 19mm (3/4") MPT icemaker d

heruntergeladen wurde: 1   Dateigröße: 1 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

6. Wipe all bin surfaces with Solution A. 7. Rinse thoroughly with clear, potable water. 8. Wipe with Solution B to sanitize. 9. Reinstall dispense wheel and other components. ! To avoid possible damage to motor assembly, use a damp cloth only. Do not allow water to run through center hole in bottom of bin area. If dispenser is equipped with chilled water accessory: 1. Remove four screws securing splash panel. 2. Disconnect 19mm (3/4") drain line from bottom of chilled water canister. 3. Loosen

heruntergeladen wurde: 1   Dateigröße: 1 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

Test operation. 11. Clean and sanitize icemaker following instructions in icemaker manual. Discard sanitized ice. 12. Clean and sanitize dispenser hopper following instructions on page 16. Installation is complete. Fig. 9 – Ice transport tube and ice level control stat mounting for freestanding dispensers and countertop units with Satellite-fill icemaker engaging pin 5mm (.187) ice tube hole ice hose mounting bracket capillary tube ice tube 26mm (1.00") 13 Installing top mount icemakers (models

heruntergeladen wurde: 1   Dateigröße: 1 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

Problem: Dispenses ice or water continuously Action PWR LED StatusCLN ICE/WTRSolution Check LEDs on control board. ON OFF ONTroubleshoot appropriate lens/sensor and replace if required (see Lens/sensor troubleshooting below). ON OFF OFF If there is power on any output terminal (WTR or WM) on control board, replace board. Remove lens protective cover; adjust funnel so water doesn’t drip down lens or behind splash panel. 21 Lens/sensor troubleshooting 1. Turn dispenser power switch off. 2. Remove

heruntergeladen wurde: 1   Dateigröße: 1 mb   Hersteller: Follett  
Kategorie: Dispenser
@name

Lift junction box and power cord up until cord and mounting screws clear notches on rear panel of dispenser. Remove Phillips head screws from right side of junction box. 8. Rotate junction box 90 degrees so that screw holes on right side of junction box align with holes on rear dispenser panel. Resecure junction box to dispenser using Phillips head screws. 9. Place power cord inside dispenser and replace access panel (Figs. 4, 5) to rear of dispenser. Note: For dispensers to be installed with ut





Kategorien