Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Grindmaster Dateigröße: 789.26 kb Dateiname: Unterrichtssprache:

Review hopper contents to make sure all parts are available: Part # Description W0600224 Manual W0600073 Rubber Pad Sheet W0600121 Merchandiser Installation Sheet W0600012 MSDS Sanitizer Sheet W0600159 Warranty Registration Card * Drip Tray Kit * Hopper Cover W0480445 Valve Handle W0631230 Valve Spring * Carb Tube * Dispense Valve Plunger W0470076 Lubricant W0631903 Sanitizer Packets W0600058 Laminated Cleaning Card W0600327 Seal Installation Instructions W0890220 4” Leg Set *Optional items specified when the unit is ordered. 8. Fill out Warranty Registration Card with the requested information and mail to Grindmaster Corporation. 9. Replace side panels. 10. Assemble the dispense valve following the instructions on page 9. The valve plunger, spring and retaining pin come in the small parts bag. 11. Be sure ON-OFF-CLEAN switch (toggle switch located underneath the electrical box) is in the “OFF” position. 12. Connect the power cord directly to a properly grounded DEDICATED 120V/60Hz, 15 Amp circuit. Do not use an extension cord. . CAUTION: Do not alter or deform the plug in any way! Altering or deforming the plug may damage unit and will void warranty. 13. Remove the drip tray kit from the bubble wrap. Separate the parts and remove the protective coating. The drip tray is mounted on two screws that are located on the lower front of the freezer cabinet. 14. Place the key hole slot of the drip tray support bracket on to these screws and tighten the screws. 15. Angle the back of the drip tray surround bracket into the drip tray support bracket and lower bracket to lock it into place. 16. Place drip tray onto drip tray surround bracket. 17. Place the louvered drip tray insert into drip tray. 18. A private label or different drink header can be installed by removing two screws from the electrical box cover. Carefully remove electrical box cover. Place the header (transparency) between the clear and opaque plates (plastic lens). Put these in place under the lip of the machine top. Slip the electrical box cover back on to machine and reinsert the screws. (see Figure F) Figure F Page 6 Crathco® Remote Beverage Freezers OPERATION AND ADJUSTMENTS How to Operate 1. Sanitize unit following the cleaning instructions starting on page 10. 2. Fill the mix storage hopper following the instructions on page 10. Allow barrel to fill with product to proper level, then insert carb tube from parts bag in hole toward rear of hopper. See Figure G. 3. Turn power switch to “ON” position. 4. Allow product to freeze in barrel. Compressor will turn off when product reaches pre-set consistency. 5. To dispense product pull down valve handle and release when done. 6. If product consistency is not as desired, adjust per the instructions on page 7. 7. Refill mix storage hopper when “mix out” light is ON. 8. Clean the unit regularly following local health codes. 9. Perform maintenance when necessary to increase the life of the unit. See chart in this manual for regular maintenance schedule. Mix Low Function These models will sense when the mix is low in the hopper. On 3341 and 3342 models, a simple float mechanism is used to sense when mix is low in the hopper. (see Figure G) When the mix level is low, the mix low light located on the front of the machine will illuminate. NOTE: Do not run the unit under mix low conditions for long periods of time. This can affect machine performance or damage componentry. On 3341A and 3352 models, mix low is sensed via the autofill system. When the mix level is low, the mix low light will illuminate continuously for 2 minutes. After 2 minutes the light will begin to blink off and on for the next 8 minutes. At the end of the 10-minute time the light will illuminate fully again. After the 10-minute cycle, the mix out safety function is activated making the unit inoperable. The safety function shuts off the autofill and refrigeration. The unit can be reset back to the freeze mode by simply adding mix into the hopper. NOTE: If the mix low safety function has activated disabling the unit, and the product has not been added for an extended period of time – verify the product is okay for re-use. If it is not, use fresh product to restart the unit. Empty the unit of old product and follow cleaning and sanitizing procedures (page 8). Consistency Adjustment From time to time, it may become necessary to readjust the consistency setting (thickness) to compensate for variation between different mixes or to switch from one type of product to another. This adjustment is made as follows: 1. Disconnect electrical power. Mix Low Float O-Ring Carburetor Mix Low Float Figure G . WARNING: Do not attempt to readjust the freezer until electrical power has been disconnected. 2. Remove right side panel (facing the freezer). 3. Use the adjustment screw, situated on the front of the drive motor mounting bracket to change product thickness. Turn the thumbscrew (3 full turns for red spring, 1 turn for yellow spring) to make a noticeable ...

Herunterladen

Geben Sie zwei Ziffern: