Stimmen - 5, Durchschnittliche Bewertung: 4.2 ( )

Hersteller: Mountain Buggy Dateigröße: 717.69 kb Dateiname: Unterrichtssprache:

The lower elastic loops fasten onto the lug below the footplate. lug lug strap WARNING: Do not leave Storm Cover on stroller in warm conditions. Check baby’s comfort frequently when using Storm Cover. STORM COVER SUN COVER REFITTING SUNHOOD Place sunhood in position and push one side of wire into plastic joint. Repeat on other side by pulling wire away from frame at the top. Fasten sunhood fabric to stroller frame and seat, near handle bar. Follow removing seat instructions above, in reverse order. Operation REFITTING SEAT . CORRECT ALL MODELS Note: Fasten seat onto frame making sure fabric wraps over and around the top of the side tubes. REMOVING SUNHOOD Pull support wire out of sunhood joint, while pushing against frame. Note:This operation is child proof and therefore requires a degree of force. Repeat step 1 on other side. sunhood support wire 3 Unfasten the sunhood fabric from the stroller frame and seat near the handle bar. 1 2 ALL MODELS REMOVING SEAT plastic joint Push seat forward, then slide fabric up seat support wire. Remove seat support wire from stroller frame at C and D. 2 2 C D seat support wire 3 A B Unfasten seat from frame along side tubes. 1 ALL MODELS URBAN Unfasten strap underneath seat at point A. Unfasten frame straps at point B. TERRAIN XSTORM COVER AND SUN COVER ACCESSORIES These accessories fasten at the top, around the side tubes. They fit over the sunhood and under the footplate. The lower elastic loops fasten onto the lug below the footplate. lug lug strap WARNING: Do not leave Storm Cover on stroller in warm conditions. Check baby’s comfort frequently when using Storm Cover. STORM COVER SUN COVER REFITTING SUNHOOD Place sunhood in position and push one side of wire into plastic joint. Repeat on other side by pulling wire away from frame at the top. Fasten sunhood fabric to stroller frame and seat, near handle bar. Follow removing seat instructions above, in reverse order. FABRIC CARE AND CLEANING This outdoor fabric should be cleaned regularly. Brush off any excessive dirt and rinse with warm water. Fabric can be removed and washed by hand using a mild natural soap solution in luke warm water (no more than 38°C / 100°F). Rinse thoroughly to remove soap. DO NOT use detergents! Allow to air dry. DO NOT tumble dry. WHEEL ALIGNMENT It may be necessary to periodically adjust wheel alignment if stroller steers to one side. The Terrain stroller has angle struts on the rear axle for this purpose. 1 Loosen all four nuts A, B, C & D holding strut in position. 2 Slightly tighten outside nut on the opposite side to the direction it is steering (eg if steering to left tighten nut D). 3 Test the stroller wheel alignment by pushing it on a smooth fl at surface. 4 Re-test the stroller steering after every turn of the nut until the stroller will run in a straight line. 5 When the correct steering is achieved, turn the outside nut on the opposite side so it just touches the side of the tube. 6 Tighten the inside nuts. HANDLEBAR GRIP Take care to protect the handlebar grip from abrasion or sharp objects. Contact your authorised dealer or distributor for replacement grips and instructions. A wetsuit glue can be used to repair cuts. Care and Maintenance Wrist strap can be used to hold stroller together in its fully folded position. Loop wrist strap around rear axle then fasten. Sunhood can be fastened back by applying velcro on sunhood window flap to the velcro on edge of sunhood. CB A D TYRES/TIRES & TUBES If a puncture occurs, the inner tube can be repaired with a bicycle repair kit, or replaced. If the tread becomes completely worn the tyre/tire should be replaced. Replacement tyres/tires, inner tubes and repair kits are available from your authorised dealer or most cycle stores. Inflating the tyres/tires: Inflate to a pressure of 15psi. (105 KPa) Do not exceed 20psi (140 KPa). The valves are the same as a bicycle, or car tyre/tire valve. WARNING: Over inflation may damage wheel. STROLLER FRAME The main frame is aluminium/aluminum and corrosion resistant. The Urban front assembly and some components are steel and will corrode if exposed to environments such as, salt water, salt spray or beach sand. If stroller is used in these environments, wash steel parts in warm soapy water, dry thoroughly and protect by spraying with light aerosol can oil eg WD40 or CRC. BRAKE STORAGE Store inside in a dry place. Make sure the stroller is dry before storing. The brake cam may require lubrication if it becomes difficult to operate. lubricate this surface brake lever wrist strap velcro TERRAIN ONLY WARNING: It may be unsafe to use replacement parts other than those supplied or approved by the manufacturer or distributor. WARNING: This stroller requires regular maintenance by the user. FABRIC CARE AND CLEANING This outdoor fabric should be cleaned regularly. Brush off any excessive dirt and rinse with warm water. Fabri...

Herunterladen

Geben Sie zwei Ziffern: