Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Mountain Buggy Dateigröße: 717.69 kb Dateiname: Unterrichtssprache:

ADJUSTING SHOULDER STRAP HEIGHT A separate safety harness conforming to British Standard BS6684 may be attached to the two “D” rings located at the insertion of the waist harness. POSITION OF CHILD IN SEAT Make sure baby is positioned down as far as possible in seat. Operation 1 2 3 insertion slit buckle shoulder straps SEAT ANGLE Seat back can be reclined to any point between upright and fully reclined position. ALL MODELS To adjust: Pull on buckles to slide straps through buckles and recline seat. Pull straps through buckles to raise seat angle. Shows upright through to fully reclined seat angle. buckles strap The Zip Hammock has two seat back positions. Seat back is upright when zips are up, and reclined when zips are down. To fasten waist strap push both buckle ends A & B into the crotch buckle C. Clip shoulder straps D & E to waist strap buckles. 21 push B A C D E clip here Adjust sliding buc kles so the harness straps are a firm fit. Move sliding buckles up as far as possible to reduce the amount of strap hanging loose, eliminating the risk of chocking. 3 sliding buckles 4 sliding buckles To release, press sides of centre buckle. 5 WRONGCORRECT XX SEAT ANGLE TERRAIN ZIP HAMMOCK OPTION REMOVING INSERTING With a hand inside the back of the seat rotate the rectangular shaped buckle and push short side through the insertion slot, while pulling strap at the front. Re-thread short side of buckle through the most suitable insertion slot for your child. Once buckle is through, turn so it is fl at against seat back, and check it is secure by pulling on strap. To locate buckle when adjusting straps, slip your hand up the inside back of the seat (or inside the pocket on the Zip Hammock model). strap short side buckle NOTE: The stroller would become unstable if a child was to move up the seat. For this reason the seat retains a slight angle to prevent the stroller from tipping back. SAFETY HARNESS Shoulder straps should be adjusted so they are located just below or level with a child’s shoulders. The older the child, the further up the seat these straps will go. ADJUSTING SHOULDER STRAP HEIGHT A separate safety harness conforming to British Standard BS6684 may be attached to the two “D” rings located at the insertion of the waist harness. POSITION OF CHILD IN SEAT Make sure baby is positioned down as far as possible in seat. Operation 1 2 3 insertion slit buckle shoulder straps SEAT ANGLE Seat back can be reclined to any point between upright and fully reclined position. ALL MODELS To adjust: Pull on buckles to slide straps through buckles and recline seat. Pull straps through buckles to raise seat angle. Shows upright through to fully reclined seat angle. buckles strap The Zip Hammock has two seat back positions. Seat back is upright when zips are up, and reclined when zips are down. To fasten waist strap push both buckle ends A & B into the crotch buckle C. Clip shoulder straps D & E to waist strap buckles. 21 push B A C D E clip here Adjust sliding buc kles so the harness straps are a firm fit. Move sliding buckles up as far as possible to reduce the amount of strap hanging loose, eliminating the risk of chocking. 3 sliding buckles 4 sliding buckles To release, press sides of centre buckle. 5 WRONGCORRECT XX SEAT ANGLE TERRAIN ZIP HAMMOCK OPTION REMOVING INSERTING With a hand inside the back of the seat rotate the rectangular shaped buckle and push short side through the insertion slot, while pulling strap at the front. Re-thread short side of buckle through the most suitable insertion slot for your child. Once buckle is through, turn so it is fl at against seat back, and check it is secure by pulling on strap. To locate buckle when adjusting straps, slip your hand up the inside back of the seat (or inside the pocket on the Zip Hammock model). strap short side buckle NOTE: The stroller would become unstable if a child was to move up the seat. For this reason the seat retains a slight angle to prevent the stroller from tipping back. Operation REFITTING SEAT . CORRECT ALL MODELS Note: Fasten seat onto frame making sure fabric wraps over and around the top of the side tubes. REMOVING SUNHOOD Pull support wire out of sunhood joint, while pushing against frame. Note:This operation is child proof and therefore requires a degree of force. Repeat step 1 on other side. sunhood support wire 3 Unfasten the sunhood fabric from the stroller frame and seat near the handle bar. 1 2 ALL MODELS REMOVING SEAT plastic joint Push seat forward, then slide fabric up seat support wire. Remove seat support wire from stroller frame at C and D. 2 2 C D seat support wire 3 A B Unfasten seat from frame along side tubes. 1 ALL MODELS URBAN Unfasten strap underneath seat at point A. Unfasten frame straps at point B. TERRAIN XSTORM COVER AND SUN COVER ACCESSORIES These accessories fasten at the top, around the side tubes. They fit over the sunhood a...

Herunterladen

Geben Sie zwei Ziffern: