Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Requires three "C" (LR14) alkaline batteries P7866 (not included) for operation. Adult assembly is required. Tool required for assembly: Phillips screwdriver (not included). Consumer Information WARNINGPrevent Entanglement Injury • Keep mobile out of baby’s reach. • Remove mobile portion of product from crib or playpen when baby begins to push up on hands and knees. • This product may not attach to all crib designs. Do not add additional strings or straps to attach to crib or playpen. • Use ONLY attached to a crib. • The mobile portion of this product may be used from birth until 5 months. • The base portion of this product may be used from birth until 36 months. • A crib mobile is intended for visual stimulation and is not to be grasped by a child. • Always attach with all provided fasteners tightly to a crib or playpen according to the instructions. Check frequently. • Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not immerse this toy. • This toy has no consumer serviceable parts. Do not take this toy apart. 2 Assembled Parts Base Mobile Note: All of the screws used to assemble this toy are attached to the product. Follow these instructions carefully to fully secure the screws. Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten. Arm Crib Connector 3 Battery Installation 1.5V x 3 "C" (LR14) • Locate the battery compartment on the back of the base. • Loosen the screws in the battery compartment door and lift to remove it. • Insert three "C" (LR14) alkaline batteries. Hint: We recommend using alkaline batteries for longer battery life. • Replace the battery compartment door and tighten the screws. • If this product begins to operate erratically you may need to reset the electronics. Slide the power/volume switch off and then back on. • When sounds or motion become faint or stop, it's time for an adult to change the batteries. • Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only). 4 Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of product in a fire. The batteries inside may explode or leak. • Never short-circuit the battery terminals. • Use only batteries of the same or equivalent type, as recommended. • Do not charge non-rechargeable batteries. • Remove rechargeable batteries from the product before charging. • If removable, rechargeable batteries are used, they are only to be charged under adult supervision. ICES-003 NMB-003 This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. L’utilisation de ce dispositif est autorisee seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit etre pret a accepter tout brouillage radioelectrique recu, meme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. 5 Assembly Crib Connector Base 1 • Fit the crib connector to the base, as shown. IMPORTANT! Make sure the straps are over the top of the crib connector. • Tighten both screws in the crib connector. • First press the button next to the socket and then slide the socket door open . • Fit the arm into the socket in the base. • Tighten both screws in the arm. PRESSSLIDE 2 Socket Arm Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. P7866a-0920 ©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA 6 Assembly Mobile Bracket 3 • Fit the mobile onto the bracket on the end of the arm. • Tighten both screws in the mobile to secure it to the arm. 7 Crib Attachment StrapsBase Crib Top Rail StrapsStraps 1 • Position the base so that the decorated side faces inside the crib. • Fit the base onto the crib top rail, as shown. • Make sure the top strap is hanging over the crib top rail. Pull the bottom strap through the crib rails. • Buckle the straps. Make sure you hear a "click". Pull on both ends of the strap to be sure it's secure. • Make sure the straps are tightened securely around the crib rail. Pull the free end of the strap to tighten. 2 Tab Tab Hint:You can secure the free end of the strap to ...