second). • To Reset the timer, press and hold the TIMER button for at least 2 seconds. If turned ON, the Alarm will sound when time expires. The alarm sounds for 5 seconds, or until cancelled by pressing any button. Setting the Timer The timer must be stopped before changing settings. The timer uses a standard setting procedure: • Press and hold “S1” to enter setting mode • Press “S2” to change the field to set • Press “S3” to change the value of the field being set • Press “S4” to exit setting

The fields are: Time setting Alarm On/Off Time setting. Press S2 until you see digits in the center of the display. Now you can set the timer. Press S3+ (lower right) to increase the timer set point, and press S3– (lower left) to decrease the set point. You will see both the digits and also the dial size increase or decrease. For a setting of 60 minutes, the dial will show completely red. Once you have set the desired time, press S2 once to change Alarm On/Off Setting. You will see the word “O

• To Stop the timer, press the TIMER button TWICE, in rapid succession (press the button twice within . second). • To Reset the timer, press and hold the TIMER button for at least 2 seconds. If turned ON, the Alarm will sound when time expires. The alarm sounds for 5 seconds, or until cancelled by pressing any button. Setting the Timer The timer must be stopped before changing settings. The timer uses a standard setting procedure: • Press and hold “S1” to enter setting mode • Press “S2” to chang

If the Alarm is OFF, pressing S2 will return you to the Time setting field. In Pre-Alarm set, you will see the word “ON” or “OFF,” plus TWO alarm •3 symbols. The Pre-Alarm symbol (smaller and on the left) will be flashing, along with ON or OFF. Press S3+ or S3– to turn the Pre-Alarm on or off. Pressing S2 again will return you to the Timer setting. Press S4 once (upper left) to exit setting mode. Leaving the watch unattended for 30 seconds in set mode causes it to save any changes and then exit

The timer can be set anywhere from one minute up to 12 hours. There is both an audible alarm and also a prealarm to let you know when time is running out or has expired. The watch comes from the factory with the timer set to one hour (indicated by 1:00 in the middle of display), and the audible alarms set to OFF. To change the settings, see instructions below. • To Start the timer, press the TIMER button (upper right). • To Stop the timer, press the TIMER button TWICE, in rapid succession (press

Press and Hold to Reset. #998-310A In the classroom, the Time Timer can be used to set time limits, measure the duration of activities and train students to make better use of available time. Use the Time Timer products to: • Time standardized tests • Monitor math and writing speed tests • Measure study periods and lunch periods • Regulate computer time • Administer duration drills • Show time left to play, get ready or clean up Using Time of Day and Alarm Press MODE (lower left) button until th

ig 'MuejjBM am ui ssajppe jaiuaQ Jieday | jssfi aqi o) uo|jejjs|6aa tpieMdois JOAjAjns I (P3jj8(3jd) iieiug jnoA ujnjaj aseay yy\QN U31SI03H (f) ffl CD w T3 CD O O » o' 3 w "D 0) 3 CD SPECIFICATIONS Batteries: Batteries should last for 18 months. If Operating Temperature: 14°F to 138°F display becomes dim. open back and replace with (-10*C to 59°C) Duraceil LR43. Eveready 186. of Ray-0*Vac LR43 Quartz Crystal Accuracy: 0.04 sec/hr (accuracy may vary wrth shock, temperature or

If necessary, Press R-Stop & L-Resetto 0. Event Split 1-2 Finish R-Start R-Start R-Start R-Stop L-Split L-Stop #1 (Repeat R,R L-Release R-Stop #2 time-in/ (Repeat L,L (See #1 time) time-out) ■ each Split) L-Release L-Reset R-Stop (See #2 time) L-Reset L-Reset TIME, CALENDARS ALARM DISPLAY Press C until you get to the Time Display. Hold R - display Month, Date, & Day Hold L - see Alarm Time Hold L & Press R - Alarm On / Off TO SET/DISARM HOURLY CHIME/ALARM Press C until you get time

Turn “off’ the timer with the power switch; reset a new timing cycle. Example 2: Elapsed Timer Indicator/Time Unknown. 1. Set power switch “on”. 2. Set timer control switch “off’. 3. Rotate “seconds” hand clockwise to the red “0” numeral. 4. Rotate “minutes” hand clockwise to the red “0” numeral. 5. Record an unknown timing event by putting the power switch in the “on” position at the beginning of the event. 6. Result: The timer records the elapsed time until the power switch is put in th

• 3090 Independence Drive, Suite 148 • Livermore, CA 94551 USA 800-935-1996 • 925-290-1900 • FAX 925-290-1930 • • support@ACCUSPLIT.com 76440 REV A