Stimmen - 6, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
12 MS7618R_062205.p65 12 22/6/2005, 15:09 Hints For Better Reception FM: The FM lead wire antenna on the back panel should be extended to its full length. You may also have to vary the direction of this antenna until you find the position that provides the best reception. AM: The AM bar antenna is inside the cabinet of the main unit. You may need to change the position of the main unit until you find the position that provides the best reception for your favorite AM stations. 13 MS7618R_062205.p65 13 22/6/2005, 15:09 14 Playing Compact Discs Note: Although this CD player can read CD-R and CD-RW discs, in addition to normal CDs, the playability of CD-R/RW discs may be affected by the type of software that was used to create the discs, as well as the quality and condition of the blank media you are using. 100% playability cannot be guaranteed. This is not an indication of a problem with the player. Normal Playback 1.) Press the POWER button on the front panel. The indicator and display light come ‘On’. 2.) If necessary, press the CD/TUNER button on the front panel to select the CD function. The two dashes “ – – ” will flash in the display. 3.) Open the CD door by lifting the OPEN/CLOSE tab on right side of CD door. If you have not already removed the white transit card from the CD player, please remove it now. 4.) Place your CD on the center spindle with the printed label side facing up. Make sure the CD is seated properly. Close the CD door. MS7618R_062205.p65 14 22/6/2005, 15:09 5.) The player will read the Table of Contents and the display will show the total number of tracks on the disc. If the disc is damaged or up side down, display will show “ – – ”. 6.) Press the PLAY/PAUSE button to begin playback on Track “01”. The indicator lights up. 7.) Adjust the VOLUME control as desired. 8.) Playback will continue until the end of the disc. When the disc ends the display again shows the total number of tracks on the disc. You may also stop playback at any time by pressing the STOP button. Pause Control To pause momentarily during playback press the PLAY/PAUSE button again. Playback stops but the disc continues to spin and the indicator flashes. Press the PLAY/PAUSE button once more to cancel Pause and resume playback. The indicator stops flashing. Skipping Tracks and High Speed Music Search During CD Playback, repeatedly press the SKIP FWD or SKIP REV buttons to skip to higher or lower number tracks. When the desired track number appears on the display, release the buttons and playback will begin on the desired track. To rapidly search forward or back within a track to locate a specific musical passage, depress and hold either the or buttons. 15 MS7618R_062205.p65 15 22/6/2005, 15:09 The player will move forward or backward at high speed as long as the or buttons are depressed. When you hear the desired passage release the buttons. Normal playback will resume at that point. Repeat Playback (On Front Panel Only) The Repeat function allows you to continuously repeat a single track, or the entire disc. The Repeat function can be activated during playback or while the player is stopped. To Repeat A Single Track Press the PLAY MODE button once. The REPEAT indicator flashes. The select the track will be repeated continuously. To Repeat The Entire Disc Press the PLAY MODE button twice. The REPEAT indicator remains ‘On’. All tracks on the disc will be repeated continuously. Repeat Playback is also canceled by pressing the STOP button, or setting to the Tuner function. Random Playback (On Front Panel Only) This feature allows you to play all the tracks on a disc in random order. Press the PLAY MODE button three times. The RANDOM indicator appears in th display. The tracks will be played in random order. After all tracks have played the player stops and the display again shows the total number of tracks. To cancel Random playback, press the STOP button. 16 MS7618R_062205.p65 16 22/6/2005, 15:09 Programmed Playback (On Front Panel Only) This feature allows you to program up to 20 tracks on a disc for playback in any desired order. You may also program a specific track to play several times within the same program. Note: You cannot program tracks while a disc is playing. If the disc is playing press the STOP button first before beginning the programming steps below: 1.) Press the CD/TUNER button to select the CD mode, insert your disc in the player, close the door, and wait until the total track number appears in the display. 2.) Press the PROG./CLOCK button once. The MEMORY indicator begins flashing in the display. “P01”appears briefly then “00”flashes. 3.) Press the or button to select the first track to be programmed. Example: Track 08. 4.) Press the PROG./CLOCK button once again to enter the track “08”in program memory number “P01”. “P02”appears briefly then “00”flashes again in the display, indicating that you may now select a track to be entered in program memory number “02”. 5.) Press the or buttons to select the n...