Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
• Is the USB memory device properly connected? Check that the USB memory device is connected to the USB terminal of this Player. • Check if the BD disc supports BD-LIVE. • Check the setting for “BD Internet Access”. (Page 42) Problem Possible causes and solutions The TV operates incorrectly. Some TVs with wireless remote control capability may operate incorrectly when using the remote control of this Player. Use such TVs away from this Player. • The Player heats up during use. When using this Player, the console cabinet may heat up depending on the usage environment. This is not a malfunction. • POWER indicator will remain lit. When the AC cord is removed from the outlet, the POWER indicator will remain lit for a short period. This is normal and is not a malfunction. • POWER indicator To Reset this Player • If this Player receives strong interference from a source such as excessive static electricity, strong external noise, malfunction of power supply, or voltage caused by lightning during use or a wrong operation is sent to the Player, errors like the Player not accepting an operation may occur. Press and hold POWER on the Player until the POWER indicator disappears. • When a reset is performed while the power is on, the Player will turn off. Turn the power on again. At this point, it may take a few moments for the system processing to finish before the Player is ready for use. During the system processing, the BD/ DVD/CD mode indicator on the Player will blink. Once the system processing has finished, the indicator will finish blinking and then light up normally. You can operate the Player when the BD/DVD/CD mode indicator is lit. • Since all settings including the language setting stored in memory are also reset when a reset has been performed, they must be set again. • When the problem persists even after performing a reset, unplug the AC cord and plug it in again. If this does not solve the problem, contact the nearest service center approved by SHARP. POWER Appendix On-screen Error Messages The following messages appear on the TV screen in case of an error during operation. Error message Cannot play. Incompatible disc. Cannot operate. This USB memory is not formatted properly. Please format the memory in USB memory management. The Connected USB Memory cannot be used. It should be compliant with USB 2.0 Possible Error • The disc cannot be played back with this Player. • If you load a disc which cannot be played with this Player (i.e. a scratched disc), or if you load a disc upside down, this message will appear, and the disc will automatically pop out. • Occurs if the loaded disc cannot be played because it is a non-standard disc or scratched, etc. • Occurs if an operation is incorrect. • Occurs if there is a formatting error. • Occurs if the USB memory is not formatted with FAT 32/16. • Occurs if USB memory not compliant with USB 2.0 High Speed (480Mbit/s) is used (i.e. USB 1.0/USB 1.1). Suggested Solution • Check the disc, and load it correctly. • Remove the disc. — Format the USB memory again. Format the USB memory with your PC. • • Connect USB 2.0 High Speed (480Mbit/s) compliant USB memory. • Specifications Specifications are subject to change without notice. General Power requirements Power consumption (Normal) Power consumption (Standby) Dimensions Weight Operating temperature Storage temperature Operating humidity TV systems Playback DC 12V (with the supplied AC adapter) 16 W (with the supplied AC adapter at AC 120V, 60 HZ) 0.4 W (with the supplied AC adapter at AC 120V, 60 HZ) Approx. 17 g 2 1/2 g 8 5/8 inch (W g H g D) Approx. 430 mm g 36 mm g 218 mm (W g H g D) Approx. 5.1 lbs. (2.3 kg) 41°F to 95°F (5°C to 35°C) –4°F to 140°F (–20°C to 60°C) 10 % to 80 % (no condensation) NTSC system Playable discs BD-ROM, BD-RE, BD-R, DVD Video, DVD+RW/+R/-RW/-R (Video/VR/AVCHD/JPEG file/MP3 file/DivX format), Audio CD (CD-DA), CD-RW/R (CD-DA/JPEG file/MP3 file/DivX format) Region code A or ALL for BD, 1 or ALL for DVD Input/Output HDMI Digital audio optical output USB input ETHERNET AC Adapter Power requirements Rated output HDMI 19-pin standard connector (1080p 24Hz output) HDMI® (Deep Color, x.v.Color, Dolby TrueHD, DTS-HD Master Audio | Essential) Terminal: Square Optical terminal USB 2.0 High Speed (480Mbit/s) correspondence (for Local storage/Software update/JPEG, MP3 and DivX playback) 10BASE-T/100BASE-TX AC 100–240V, 50/60Hz DC 12V, 5A Appendix (Continued on the next page) Specifications Wireless LAN (Internal antenna) Frequency band Modulation Transport power and sensitivity Security Tx output power: (Typical) Draft 802.11n Radio: 2.4GHz 802.11g Radio: 2.4GHz 802.11b Radio: 2.4GHz 2.412 – 2.462GHz (channel 1–11) DBPSK @ 1Mbps DQPSK@ 2Mbp CCK@ 5.5/11 Mbps BPSK@ 6/9 Mbps QPSK@ 12/18Mbps 16-QAM@ 24/36 Mbps 64-QAM@ 48/54 Mpb and above, Rx up to 300Mbps 11b 16.5 +/- 1 dBm 11g 16 +/- 1 dBm@54Mbps 11n 15 +/- 1 dBm Rx sensitivity: (Typical) -84 dBm @11 Mbps -72 dBm @54 Mbps -64 dBm @64-QAM, 20MHz channel ...