Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
B (Aug. 2001) MODEL MG1532 MIXER-GRINDER MODEL MG2032 MIXER-GRINDER © HOBART CORPORATION, 1997 – 2 – Installation, Operation, and Care of MG1532 & MG2032 MIXER-GRINDERS SAVE THESE INSTRUCTIONS GENERAL The MG1532 & MG2032 Mixer-Grinders are designed to use a #32(42/46) size knife and plate (knives and plates are available at extra cost but not included with grinder). Do not use a plate with hole size smaller than 3/32". The MG1532 Mixer-Grinder is equipped with either a 5 or 71/2 HP Grind Motor and a 1 HP Mix Motor. The MG2032 Mixer-Grinder is equipped with a 71/2 HP Grind Motor and a 1 HP Mix Motor. On all models, the worm rotates at 216 RPM and the mix arm rotates at 23 RPM. The MG1532 with 5 HP Grind Motor is for fresh meat only, not for frozen product. The inclined hopper permits lower, easier loading while the tilted worm provides a convenient output height. Releasing the latch handle allows the hopper guard (lid) to open easily — torsion springs counterbalance the lid's weight. The exclusive Hobart designed #46 Wedge cylinder grinding end speeds product from hopper to grinding end by pulling pieces of meat through the large upper opening of the cylinder (Fig. 1). The MG1532 & MG2032 Mixer-Grinders may be ordered with any of the following options and/or accessories: 1) Caster sets and / or adjustable leg sets. The MG1532 & MG2032 Mixer-Grinders are equipped with flexible power supply cord and plug. Either a receptacle or a pendant type connector is available. The receptacle requires a type FD electrical box (not supplied). 2) Pneumatic foot switch accessory (can be easily added at any time). Fig. 1 3) The hopper side-feed inlet can be ordered (and factory installed) for the right side of the hopper to allow product from a companion first cut grinder to feed directly into the hopper. A plug assembly for the side feed inlet, a drip cup, and adapter ring for the first-cut grinder are available accessories. The MG1532 hopper can hold up to 150 pounds of fresh meat. The MG2032 hopper can hold up to 200 pounds of fresh meat. The MG1532 & MG2032 Mixer-Grinders can grind at a rate of 55 to 60 pounds of fresh boneless beef per minute, first or second cut through a 1/8" plate. Pork can be ground first cut through a 3/4" breaker plate and second cut through a 3/16" plate at 60 to 65 pounds per minute. Up to 60 pounds of frozen meat per batch (on units with 71/2 HP Grind Motor only) can be ground from flake or stick form when tempered to 26°F or higher and first grind is through a 3/8" or larger plate. – 3 – INSTALLATION Immediately after unpacking the mixer-grinder, check for possible shipping damage. If the machine is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to make sure it agrees with the specifications on the machine data plate (Fig. 5). CASTER SETS AND / OR ADJUSTABLE LEG SETS With the mixer-grinder securely elevated using the base frame for support, bolt the caster assemblies through the corner holes using four hex-head 5/16-18 bolts, lockwashers, washers, and nuts for each caster, provided. • When equippped with two Fixed and two Swivel casters, install Fixed Casters- without-Brake on rear corners of the machine and Swivel Casters-with-Brake on front corners. • On machines with four identical legs or casters, install one on each corner. All casters and leg sets use washers under the flange and above the machine base frame. Insert bolt up through the flange from the bottom with the lockwasher next to the nut on top (Fig. 2). LEVELING Level the mixer-grinder, both front-to-back and side-to-side, by loosening the two set screws on the caster shaft (Fig. 2) and screwing the caster up or down. Tighten both set screws when level. LUBRICATION The mixer-grinder is shipped with oil already installed. If oil loss is observed, the oil levels of both transmissions should be checked prior to operation. Contact Hobart Service. PNEUMATIC FOOT SWITCH To install the pneumatic foot switch, remove the lower front panel (6 screws). Remove the knockout from the bottom front floor panel inside the machine compartment (Fig. 3) and insert the tube from the foot switch through the knockout hole. Remove the cap from the barbed fitting at the bottom left side of the control box (Fig. 3) and connect the tube from the pneumatic foot switch onto the barbed fitting using the clamp provided. A pliers will be needed to squeeze the clamp open during installation. Avoid kinking the tube. NUT MACHINE BASE FRAME LOCKWASHER WASHER WASHER BOLT BRAKE GREASE FITTING SET SCREW PL-52464 Fig. 2 KNOCKOUT CONTROL BOX BARBED FITTING Fig. 3 – 4 – ELECTRICAL CONNECTION WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIR...
Dieses Handbuch ist für folgende Modelle:Standmixer - MG1532 (486.71 kb)