Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Reconnect the power supply and push the MIX-GRIND START switch to verify that both the worm and the mixer arm rotate counterclockwise as viewed from the front of the machine. – 5 – CONTROL BOX HEATERS The Mixer-Grinder has a heater in the control box and another heater in the front control panel to keep the controls dry. They are automatically ON when the machine is electrically connected. The Mixer- Grinder should always be connected EXCEPT when performing assembly, disassembly, cleaning, or maintenance of the machine. After cleaning, reconnect the electrical power supply. OPERATION CONTROLS (Fig. 4) FOOT SWITCH MIX START STOP FOOT SWITCH OFF ON MIX/GRIND START Fig. 4 MIX START Button— Starts rotating the mix arm. Use the Stop Button to stop mixing. STOP Button — Turns the mixer-grinder off. Turns the Foot Switch off if it was on. MIX/GRIND START Button — Starts rotating both mix arm and worm. Use the Stop Button to stop mixing and grinding. FOOT SWITCH — When On, the Mix Start and Mix/Grind Start Buttons are inoperable and the accessory Foot Switch can be used to Mix/Grind ONLY. The indicator light shows when the Foot Switch is On. Push the STOP Button to turn the Foot Switch Off. HOPPER LID INTERLOCK — An interlock switch requires the hopper lid to be closed before the machine can operate. Raising the hopper lid opens the electrical circuit and makes the machine inoperative. PL-41181-1 HOPPER LID LATCH GRINDER CYLINDER ADJUSTING RING MACHINE DATA PLATE BUSHING RETAINER FLANGE NUT Fig. 5 – 6 – GRINDER ATTACHMENT The Wedge cylinder is marked TOP and BOTTOM. Before operating, make sure TOP is visible. The grinder attachment can easily be removed for cleaning (see Cleaning, page 8). Use the spanner wrench to loosen the adjusting ring and remove the adjusting ring, plate and knife. Next loosen, but do not remove the grinder attachment's two flange nuts, using the spanner wrench. Rotate the cylinder clockwise and remove the cylinder; then, remove the worm. At reassembly, install the worm and then the cylinder. Make sure TOP is visible on the cylinder and that the cylinder's flange nuts are tight before assembling the knife, plate, and adjusting ring. Use only the flange nuts provided. Two studs on the front of the machine allow storage of the spanner wrench and pneumatic foot switch. The rubber seal at the drive end of the worm can be removed by hand for cleaning. Grasp the outer flange of the seal or use a dull screwdriver to pry the seal loose. Reinstall seal before installing worm. Before using the grinder attachment, take it apart and thoroughly wash it. The knife and plate need some preliminary lubrication: Rub tallow or food grade mineral oil over the cutting faces of these parts. When assembling the knife, be sure to turn the cutting side towards the perforated plate. The notch on the circumference of the plate must fit over the pin in the cylinder. Knives and plates must be sharp and true for proper cutting action. Keep the grinder attachment in a clean and sanitary condition. PL-40984-1 WORM SEAL MIX ARM SEAL MIX ARM WORM Fig. 6 MIXING ARM Loosen the bushing retainer's two flange nuts and remove the bushing retainer (Fig. 5). Raise the hopper lid and pull the mixing arm from the square drive end, lifting the mixing arm from the hopper (Fig. 6). When reassembling, make sure TOP on the bushing retainer is “up” so the mixing arm runs straight between the round bushing and the square drive-end. Remove the mixing arm after disassembly of the grinder cylinder and worm. Reassemble the mixing arm before assembly of the grinder cylinder and worm. MIXING AND GRINDING The MG1532 has a hopper capacity of up to 150 pounds of fresh meat depending on the type of product. The MG2032 has a hopper capacity of up to 200 pounds of fresh meat depending on the type of product. Don't put frozen product in units with 5 HP Grind Motor. Second cut meat may be mixed in the hopper for any desired length of time. During the MIX operation, the mixing arm rotates and the grinder worm does not. Continuous self-feeding occurs along with grinding in the MIX-GRIND operation. Mixing of uncut or unground meat is not recommended. Grinding Procedure First Grind . . . Fill hopper and close and latch the hopper lid. Overfilling will bend the hopper lid and may cause the interlock to open the electrical circuit. Push MIX-GRIND Button to start grinding. Press STOP Button to stop grinding. Second Grind . . . Fill hopper and close and latch the hopper lid. Press MIX Button. After desired mixing, press the STOP Button. Then, press the MIX-GRIND Button to start grinding; press the STOP Button to stop grinding; or activate and use the optional accessory Foot Switch. – 7 – CLEANING WARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY BEFORE CLEANING OR SERVICING THIS MACHINE. In any cleaning operation after disconnecting the electrical power supply, seal the receptacle to prevent entrance of moisture. To make this seal on Hobart supplied receptacles and ...
Dieses Handbuch ist für folgende Modelle:Standmixer - MG2032 (486.71 kb)