Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Remove any labels or stickers from the unit. To remove any dust that may have accumulated during packaging, clean the electric food and cheese grater and its parts thoroughly before using for the first time, according to the instructions in the “Cleaning Your Food and Cheese Grater” section of this manual. OPERATING YOUR ELECTRIC FOOD AND CHEESE GRATER RECHARGING: 1) Fully charge unit before use. To start the battery recharge, place the charger plug (11) into a 120V/60Hz AC only outlet. 2) To place the grater into the rechargeable base (10), face the grating end of the unit downward into the rechargeable base. (Figure 1) By doing this, the handle of the grater should be facing upwards and will be easily accessible. 3) Once the unit is fitted into the rechargeable base the charging indicator light (12) will illuminate letting you know that the unit is in the process of recharging. 4) To be sure the electric grater is fully charged, leave it in the rechargeable base for about 15 hours. This will allow the unit to operate at full power. 5) The handle will become warm during recharging. This is normal. 6) If the grater does not work, check to make sure it was properly positioned in the rechargeable base. FIGURE 1 NOTE: If the operation time seems to have shortened, it does not mean that the electric food and cheese grater is defective. This problem may be solved by leaving the grater “on” until the stainless steel grating drum (2) stops turning. Then recharge the appliance for 15 hours. This procedure improves the battery’s recharging capacity. If necessary, repeat this operation more than once. WALL MOUNTABLE: The rechargeable base has an optional wall mountable feature. To mount the rechargeable base to your wall follow these directions: 1) Place the rechargeable base on a desired point on the wall. 2) Then mark the points in the two drill holes located on the bottom of the rechargeable base with a pencil. 3) Remove the rechargeable base from the wall. Drill holes into the wall according to your two pencil marks. Place the rechargeable base back onto the wall after the holes have been drilled. Align the holes on the bottom of the rechargeable base with the holes in the wall. 4) Turn screws into the holes with a screwdriver until the rechargeable base fits tightly on the wall. Screws not included. OPERATING YOUR ELECTRIC FOOD AND CHEESE GRATER (con’t) 1) Remove dust cover (1) from end of grater before operation. (Figure 2) 2) Cut food into small squares. If you are grating cheese, remove the skin of the cheese before grating. Place cut food into the top opening of the food receiver (4) and push down. (Figure 3) FIGURE 2 FIGURE 3 3) Lower the lever (6) and press the on/off and pulse switch (7) located on the lever to grate food. Be sure to have either a plate or bowl to catch the grated food. Or you can grate directly over the food being served. 4) To terminate operation discontinue pressing the on / off and pulse switch. Wait until the stainless steel grating drum (2) has stopped rotating completely. Place your finger inside the stainless steel grating drum and rotate counter-clockwise about a 1/4 turn and carefully remove it for cleaning. (Figure 4) See the “Cleaning Your Electric Food and Cheese Grater” section of this instruction manual for details. 5) To replace the stainless steel grating drum (2), slide it back into the opening and rotate clockwise by about a 1/4 turn. You will hear a click, indicating that the stainless steel grating drum has locked into place. 6) After use, carefully dismantle detachable parts. First, remove the stainless steel grating drum (2) according to direction number 4 in the “Operating Your Electric Food and Cheese Grater” section of your instruction manual. Second, lift the lever (6) and pull out the food receiver (4). (Figure 5) FIGURE 4 FIGURE 5 OPERATING YOUR ELECTRIC FOOD AND CHEESE GRATER (con’t) 7) Then separate the food receiver (4) from the external protector (3) by pulling outward. (Figure 6) To put the food receiver and the external protector back together, align the three grooves with the three notches on the external protector. (Figure 7) Press slightly until you hear a click. Place the unit back into the machine body (8) and press slightly until you hear a click. 8) To remove the rubber press (5), pull it out of its housing. (Figure 8) To replace the rubber press, put it back in its housing and press down. (Figure 9) Make sure that the tongue matches the slot on the lever. FIGURE 6 FIGURE 7 FIGURE 8 FIGURE 9 CLEANING YOUR ELECTRIC FOOD AND CHEESE GRATER 1) CAUTION: Be sure to switch off this appliance before cleaning the body and its attachments. To protect against electrical shock, do not immerse charger cord, plug or rechargeable base in water or liquid. 2) The dust cover, stainless steel grating drum, external protector, rubber press and food receiver are all dishwasher-safe parts. Alternatively, they can also be washed by hand with warm water and mild soap, an...