Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Always inspect cutting assembly for broken, cracked, or loose blades. If jar or cutting assembly is damaged, do not use. Call our toll-free customer service number to obtain replacement parts. 1. Make sure blender is unplugged. Place blender base on clean, dry surface. 2. Fit gasket over blades as shown in illustration on page 4. The gasket must lie flat. Set jar on top of gasket and screw on cutting assembly. Make sure the cutting assembly is firmly screwed onto the jar. 3. Set jar into place on blender base, making sure it is securely seated. If not, gently rock the jar until seated. OPTIONAL: When dispenser is not needed, replace dispenser with spout cap. Remove dispenser by rotating counterclockwise (see “How to Clean” section). Insert spout cap on jar. Turn spout cap clockwise to tighten. 4. When spout cap is not in use, snap onto bottom of blender base for storage. How to Operate 1. Plug cord into outlet. 2. Put ingredients in jar. Place lid with filler cap on jar. 3. Process food or beverages. See the “Blending Specific Foods” section for speeds and processing tips. NOTE: When blending thin liquids, do not fill above the 32-ounce/ 4 cup/1200 ml mark on blender jar. 4. ALWAYS turn blender off and wait until blades have stopped rotating before removing jar. 5. To remove jar after blending is complete, lift the jar straight up. If it is not easily removed, rock gently and lift. Do not twist. To Use the Dispenser: To dispense thick liquids (such as milkshakes, smoothies, frozen drinks, etc.), turn the control knob to DISPENSE and pull Dispenser Lever up. Turn OFF after dispensing. NOTE: Blender MUST be ON to dispense thick liquids and frozen drinks. When dispensing thin liquids, it may not be necessary to turn the blender ON to dispense the liquid. NOTE: NEVER replace jar onto unit while motor is running. 5 840155501 ENv01.qxd 2/26/08 1:43 PM Page 6 How to Clean Quick Cleaning Quick cleaning should only be used to rinse the blender between batches of processing the same food. When the processing of a single type of food is finished, the blender should be disassembled and thoroughly cleaned as instructed below. To quick clean, pour 2 cups (500 ml) warm water in jar and add 1 drop liquid dishwashing detergent. Run the blender on DISPENSE for 10 seconds. Flush soapy water through dispenser until Regular Cleaning cleaned. Discard soapy water. Rinse blender jar with clean water. Flush clean water through dispenser until cleaned. This function is not a substitute for regular cleaning as instructed below This function should never be used when blending any mixture containing eggs, milk, or any other dairy products. wWARNING Electrical Shock Hazard. Disconnect power before cleaning. Do not immerse cord, plug or base in any liquid. 1. Unplug blender from electrical outlet. 2. Wipe blender base and cord with a damp cloth or sponge. To remove stubborn spots, use a mild, nonabrasive cleanser. 3. To clean jar, unscrew cutting assembly from jar. 4. Carefully remove gasket from cutting assembly. 5. Remove dispenser assembly from jar by turning counterclockwise four revolutions. NOTE: DO NOT remove seal rings from dispenser adaptor. 6. Carefully wash cutting assembly, gasket, jar, and lid in hot, soapy water. Rinse and dry thoroughly. Do not soak. Do not wash cutting assembly or gasket in a dishwasher. NOTE: All parts except the cutting assembly and gasket may be washed in the dishwasher (on the top rack only). Some part distortion may occur if your household dishwasher temperature is higher than normal or if the parts are placed too close to the heating element. 7. Reassemble cutting assembly and gasket onto jar, and replace jar onto blender base. Ensure dispenser assembly or spout cap are fully rotated clockwise to lock into position (reverse of Step 5 above). 8. Store blender with lid or filler cap removed to prevent container odor. 6 840155501 ENv01.qxd 2/26/08 1:43 PM Page 7 Optional Cleaning 1. Remove dispenser assembly cap by 3. Reassemble plunger inside of dis- rotating coun-penser body and rotate cap terclockwise. clockwise until tight. 2. Wash dispenser and parts in hot, soapy water. Rinse and dry thoroughly. Do not soak. NOTE: Do not remove seal rings from adaptor. Dispenser Assembly Cap Dispenser Assembly Body Adaptor Seal Rings Plunger Troubleshooting PROBLEM PROBABLE CAUSE/SOLUTION Blender leaks. • Tighten cutting assembly on jar. • Make sure gasket is in place on cutting assembly. • Make sure gasket is not damaged. If damaged, please call our toll-free customer service number to order a replacement. • Make sure lid with filler cap is pushed down tightly on jar. Ice not crushed. • See ice crushing instructions in “Blending Specific Foods” section. Does not blend well. • Make sure enough liquid has been added. A minimum of 10 ounces (300 ml) is recommended. Does not dispense. • Make sure blender is ON. Dispenser leaks. • Make sure seal rings are in place on dispenser adapter. • Tighten dispenser cap (locate...