Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
It is not intended nor approved for use in an industrial or residential environment. Caution—This device is not intended nor approved for connection to the public ISDN telecommunication network. Attention—Ce dispositif n'est pas prevu ni approuve pour le raccordement au reseau de telecommunication public le RNIS. Vorsicht—Dieses Gerat ist nicht fur Anschaltung an das offentlich ISDN Telekommunikationsnetz genehmigt. Precaucion—Este dispositivo no esta previsto ni se ha aprobado para la conexion a la red de telecomunicaciones publica ISDN. Attenzione—Questo dispositivo non e inteso ne non approvato per collegamento alla rete di telecomunicazione pubblica ISDN. Document Number: 13228U7-001 Rev. B Sales Office: +1 (301) 975-1000 Part Number: 07MSDTA-QS Technical Support: +1 (301) 975-1007 Revised: July 23, 2007 E-mail: support@patton.com WWW: • The Smart-DTA contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel. WARNING • Mains Voltage: Do not open the case the power cord is attached. The external power adaptor shall be a listed limited power source that incorporates a disconnect device and shall be positioned within easy reach of the operator. The mains outlet shall be within 10 feet (3 meters) of the device, shall be easily accessible, and protected by a circuit breaker. • The Smart-DTA is not shipped with power cables. For AC powered units, ensure that the power cable used meets all applicable standards for the country in which it is to be installed, and that it is connected to a wall outlet which has earth ground. • Hazardous network voltages are present in WAN ports regardless of whether power to the Smart-DTA is ON or OFF. To avoid electric shock, use caution when near WAN ports. when detaching the cables, detach the end away from the Smart-DTA first. • Do not work on the system or connect or disconnect cables during periods of lightning activity. 1.0 Power up the Smart-DTA The terminal block header to which the wires are secured provides the disconnect for the Smart-DTA. Take proper measures to ensure that it is not permanently fastened to the receptacle mounted on the chassis. CAUTION 1. Connect the Smart-DTA to a power source using the included power supply and cable. 2. When the Power LED stops blinking and remains lit, the Smart-DTA is ready to configure. Smart-DTA Quick Start Guide 2.0 Connect the Smart-DTA to your local network You must connect the Smart-DTA to an IP network that provides a DHCP server. Using the included black Ethernet cable, connect the Smart-DTA RJ-45 Ethernet WAN port, labeled ETH (see figure 1), to an Ethernet hub or switch on the same network as your PC. The Ethernet WAN interface is configured as a DHCP client. DHCP Server Ethernet Hub or Switch Smart-DTA PC ETH port Figure 1. Connecting the Smart-DTA to the network via a hub or switch Smart-DTA Quick Start Guide 3.0 Connect the Smart-DTA to an ISDN phone 1. Using a straight-though cable, terminated with RJ-45 connectors, connect the BRI port of your Smart-DTA to the S/T port of your ISDN phone, as shown below: ISDN Phone RJ-45, male RJ-45, male 3 3 4 4 5 5 6 6 Note: Other pins are not used. Smart-DTA Quick Start Guide 4.0 Start the SmartNode Discovery Tool 1. Insert the CD included with your Smart-DTA into the CD drive on your PC. 2. Copy the file named SNDiscovery.exe from the CD to your PC. 3. At your PC, double-click the SNDiscovery.exe file name to activate the tool. The SmartNode Discovery Tool window will display the IP Address, MAC Address, Device Type (model number) and Build (software release) of your Smart-DTA. If your Smart-DTA does not appear: • Make sure the Smart-DTA and your PC are on the same routed subnet • Make sure any firewall programs on your PC are disabled 5.0 Access the Web Browser (GUI) Interface 1. In the SmartNode Discovery Tool window, select the line that displays the IP address of your Smart-DTA. Figure 2. SmartNode Discovery Tool window Smart-DTA Quick Start Guide 2. Right-click the selected line, and select Webbrowser. The Login window will display. Figure 3. Login window 3. Enter the username administrator. Do not enter a password. Instead simply click OK. Your web browser will display the Smart-DTA home page. Figure 4. Smart-DTA home page 6.0 Configuring your Smart-DTA Once you have logged in you can use the browser-based graphical user interface (GUI) to configure and manage your S-DTA. The Smart-DTA home page displays three Immediate Actionsbuttons that allow you to store the current configuration state, reload the device, and restore to factory defaults. The home page also displays certain basic system information. You can always return to the home page by clicking Home in the navigation bar. Smart-DTA Quick Start Guide The GUI consists of the following main elements: • The “Navigation Bar” on the left edge presents you with a menu listing giving access to the various configuration...