RIVETS TIRA EXTER. CON. REMACHE 5 704 558 092 000 SICHERHEITSLASCHE 3/8" .050" SAFETY TIE STRAP ECLISSE DE SECURITE TIRA SEGURIDAD 5 710 1 1 1 1 1 1 952 100 130 SAGEKETTENSCHUTZ CHAIN PROTECTION COVER ENVELOPPE PROTECTRICE ESTUCHE PROTECTOR 5 710 1 1 952 100 140 SAGEKETTENSCHUTZ CHAIN PROTECTION COVER ENVELOPPE PROTECTRICE ESTUCHE PROTECTOR ES-153 A ES-2130 A ES-163 A ES-2135 A ES-173 A ES-2140 A ES-183 A ES-2145 A Inhaltsverzeichnis Index Table des matières Indice

Chain saws with significantly reduced kickback potential are available. 19 5 7 6 5 4 1 2 3 Lift the chain (6) over the sprocket (5). Using your right hand, guide the chain into the top guide groove on the guide bar (7). CAUTION: Note that the cutting edges along the top of the chain must point in the direction of the arrow! Position the guide bar (4) and push against the sprocket (5) as shown by the arrow. Mounting the guide bar and saw chain Use the universal wrench delivered with the chain saw

Ensure that the WARNING: power cord is disconnected before performing any maintenance on your saw. Sprocket Tip Lubrication The sprocket tip on CAUTION: your new saw has been pre-lubricated at the factory. Failure to lubricate the guide bar sprocket tip as explained below will result in poor performance and seizure, voiding the manufacturer’s warranty. Lubrication of the sprocket tip is recommended after each saw use. Always thoroughly clean guide bar sprocket tip before lubrication. The Lube Gu

Lubrication of the sprocket tip is recommended after 10 hours of use or once a week, which ever occurs first. Always thoroughly clean guide bar sprocket tip before lubrication. The Lube Gun (optional) is recommended for applying grease to the guide bar sprocket tip. The Lube Gun is equipped with a needle nose tip which is necessary for the efficient application of grease to the sprocket tip. Fig. 37 To lubricate the sprocket tip: 1. Move the STOP switch down. NOTE: It is not necessary to remove

. . . . . . . . . .13 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .19 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Warranty Information . . . . . . . . . . . . . . . . . . . . . . .20 Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover Copy the model and parent part number here: Copy the serial number here: Make sure you carefully read and understand this manual before starting or operating this equipment. THIS PRODUCT IS COVERED

A bottle brush can come in handy for cleaning out the cylinder ribs. With the cyinder fin cleaner, clean out the area between the cylinder fins and between the cylinder and the mounting plate. Do not use force. Be careful not to damage the short-circuit wire and the ignition wire. Mounting the fan housing Put the fan housing (13) on. Press the screws (14) into their holes. Lift the engine hood (15) slightly and use your thumb to hook in the tab (16) on the fan housing. Straighten out the fan hou

RIVETS TIRA EXTER. CON. REMACHE 5 704 558 092 000 SICHERHEITSLASCHE 3/8" .050" SAFETY TIE STRAP ECLISSE DE SECURITE TIRA SEGURIDAD 5 710 1 1 1 1 1 1 952 100 130 SAGEKETTENSCHUTZ CHAIN PROTECTION COVER ENVELOPPE PROTECTRICE ESTUCHE PROTECTOR 5 710 1 1 952 100 140 SAGEKETTENSCHUTZ CHAIN PROTECTION COVER ENVELOPPE PROTECTRICE ESTUCHE PROTECTOR ES-153 A ES-2130 A ES-163 A ES-2135 A ES-173 A ES-2140 A ES-183 A ES-2145 A Inhaltsverzeichnis Index Table des matières Indice

RIVETS TIRA EXTER. CON. REMACHE 5 704 558 092 000 SICHERHEITSLASCHE 3/8" .050" SAFETY TIE STRAP ECLISSE DE SECURITE TIRA SEGURIDAD 5 710 1 1 1 1 1 1 952 100 130 SAGEKETTENSCHUTZ CHAIN PROTECTION COVER ENVELOPPE PROTECTRICE ESTUCHE PROTECTOR 5 710 1 1 952 100 140 SAGEKETTENSCHUTZ CHAIN PROTECTION COVER ENVELOPPE PROTECTRICE ESTUCHE PROTECTOR ES-153 A ES-2130 A ES-163 A ES-2135 A ES-173 A ES-2140 A ES-183 A ES-2145 A Inhaltsverzeichnis Index Table des matières Indice