It will return to original status if not adjusted in 5 seconds. Note: This function is operated by using remote control only. 10 9 Rotate © button clockwise, make the first number “0” increase to “ 1" , then LCD will show “ 131 ” ; 0 Pressing© button will play the 131th track. *File Search For example:The structure of the tracks in the disc or in the USB is as follows, find the 3.MP3 track in 3 areas through file search. DISC- —larea- -2 area- -1.MP3 2. MP3 'S. MP3 1.MP3 -2. MP3 —3

Good locations include under a seat, in the trunk or hatch area. * Please remember this is a high power unit which generates high electrical energy and heat. Therefore be sure to install the unit in a place with sufficient airflow, a minimum of dust and no moisture. Allow enough space around the cooling fins to permit reasonable airflow and cooling. It is important to ensure that the cooling fins of the heat sink are not against a panel or a surface preventing air circulation. * Never mount th

Low level signal is carried through RCA cables, it is preferred to use low level inputs to the amplifier if the head unit is equipped with the low level outputs. SPEAKER OUTPUT CONNECTIONS You do not need to make any adjustment for the input connection of amplifier before you connect the speaker output. * Connect right and left speaker wire to corresponding speaker output terminals of the amplifier. * Be sure to have the positive wire from the speaker to the positive speaker terminal of the

And the ground cable gauge should be the same as the +12V DC. * Connect the +12V Power terminal to the battery (+) position terminal. An in-line fuse must be installed in the +12V power cable near the battery less than 50mm. Without one, an accidental short circuit could pose a fire hazard and damage your amplifier. Connect the fuse holder to battery, however, do not install fuse at this time. * Connect the GROUND Power terminal directly to the battery (-) position terminal or the car chassis.

OR HANDLE OTHER CUSTOMER SERVICE SITUATIONS PYLE SERVICE CENTER 1600 63RD STREET Brooklyn. NY 11204 !-800-934-2277 Monday Through Thursday. 9AM to 5PM Friday 9AM то 2PM Eastern. WWWPYLEAUDIO.COM РУ1.Е № © Congratulations on purchasing the High Speed Power Amplifier. The amplifier has been designed using the latest electronic technology available, allowing you to produce high quality stereo reproduction in mobile applications. This system provides you with low harmonic distortion, a huge cons

Reversing any of these connections will result in the speaker cones moving out of phase which causes bass cancellation. LEVEL CONTROLS Turn the VOLUME control on the amplifier to Min initially. Once the initial power sequence has been performed, set the CD/RADIO volume control to roughly 80% of full. Insert a CD or tune to a radio station and slowly turn up the amplifier VOLUME control until you hear some distortion, and then back it off for clean sound. 5 2 CHANNEL AMPLIFIER - APPLICATIONS

wiring tips fuses Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wire less than one meter (39") in length. Use 4 gauge wire. Connect the remote terminal to the remote output of the head unit using 14 gauge. Connect an empty fuse holder within 300mm (12") of the battery and 4 gauge or larger high quality cable from this fuse to the amplifier location. Make sure there is no fuse in this fuse holder. Then make the connection to the "BATT" connecti

Couple the RCA input with the car stereo or equalizer outputs using RCA type connector cables. 5. POWER FUSE Power fuse protects both this amplifier and the automobile electrical system from wrong electrical conditions. 6.POWR SUPPLY TERMINAL Connect the +12V DC power supply into the terminal by lugs and screws accessible at the panel of this amplifier. A.BATT +12V Connect +12V DC power supply wire into the terminal from the terminal of the battery. B.GROUND Ground terminal connect the g

You may use 4 to 8 ohms speakers. Before connecting, please check speaker connection diagrams. 2 ELECTRICAL & AUDIO CONNECTIONS A. STEREO INPUT CONNECTION I.High impedance input. 2.Low impedance (BTL or Common Ground) Input a.Four Speaker Output Mode a-1. Floating Ground Type CAR STEREO Figure 3 3 ELECTRICAL & AUDIO CONNECTIONS a-2. Common Ground Type Figure 3A b.Two Speaker Output Mode b-1. Floating Ground Type Tf "F 'nf T’ "if "if "iF "ii—A Figure 4 4 ELECTRICAL & AUDIO CONNEC

Be sure to mount the amp in such a manner as to allow reasonable airflow over the cooling fins. Mark the location for the mounting screw holes by positioning the amp where you wish to install it and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen. Before attempting to drill the mounting holes, take note of any wires, lines or other devices i