Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Elevation Audio Dateigröße: 6.73 mb Dateiname: Unterrichtssprache:

nal preference while listening to the system. Crossover Gain O I O @Q * Ô :OOlboll O DX200.2 DX300.4 Crossover Gain Subsonic DX500.1 DX1000.1 DX2000.1 Crossover Gain Gain Crossover ^^_A- 9 Operation STRAPPING AMPLIFIERS CDX5CJO/I /DX1DOD.1 /DXSOaO.I ] The DX500.1/DX1000.1/DX2000.1 amplifiers have the ability to connect two together and have their outputs combined, or strapped, to power a single speaker load. /j\ CAUTION: Two DX500.1/DX1000.1/DX2000.1 amplifiers that are strapped together are not recommended for impedance loads below 2 Q . 1. Select which amplifier of the two will be the master, and set the Master/Slave switch in the "out" position. NOTE: Only adjustments made to the master amplifier will effect the output to the connected speaker- 2. Connect RCA cables from the source signal to the input connection on the master amplifier. 3. Set the Master / Slave switch on the slave amplifier to the "in" position. 4. Connect a RCA cable from the MAS OUT connector on the master amplifier to the SLV IN connector on the slave amplifier. 5. Connect one of the negative (-) speaker outputs from the master amplifier to one of the negative (-) speaker outputs on the slave amplifier using a 10 gauge wir e (minimum). 6. Connect one of the positive (+) speaker outputs from the master amplifier to the positive (+) terminal of the speaker being use. 7. Connect one of the positive (+) speaker outputs from the slave amplifier to the negative (-) terminal of the speaker being use. From Source Unit ■ II Symptom Diagnosis Remedy Amplifier does not turn on. B+ or REM not between 10.5 and 15.5 volts or no voltage present Check the alternator, battery, fuse, and wiring and repair as necessary Amplifier Noise Amplifier is not properly grounded. Check wiring and repair as necessary (Turn-On Pop) Voltage spike from source unit is entering amplifier's input Connect a relay turn-on module to REM terminal if pops are eliminated with no input signal to amplifier Engine Noise Noise is radiating into signal cables Re-route signal cables away from sources of high current 10 Specifications MODEL : DX500.1 Continuous Power Rating (RMS) - Measured at 14.4 Battery Volts 4 £2 Load Per Channel 200 Watts x 1 2 £2 Load Per Channel 300 Watts x 1 1 £2 Load 500 Watts x 1 Amplifier Fuse Rating (Amp/Type) (2) 30A / AWG Dimensions: Height 2.0" (5.08cm) Width 10.5" (26.67cm) Length 12.25" (31.11cm) DX1000.1 350 Watts x 1 600 Watts x 1 1000 Watts x 1 (3) 30A / AWG 2.0" (5.08cm) 10.5" (26.67cm) 15.75" (40.00cm) DX2000.1 700 Watts x 2 1200 Watts x 2 2000 Watts x 1 (4) 30A / AWG 2.0" (5.08cm) 10.5" (26.67cm) 17.72" (45.00cm) MODEL : DX200.2 Continuous Power Rating (RMS) - Measured at 14.4 Battery Volts 4 £2 Load Per Channel 75 Watts x 2 2 £2 Load Per Channel 100 Watts x 2 4 £2 Load Bridged (Mono) 200 Watts x 1 Amplifier Fuse Rating (Amp/Type) (1) 30A / AWG Dimensions: Height 2.0" (5.08cm) Width 10.5" (26.67cm) Length 10.24" (26.00cm) DX300.4 50 Watts x 4 75 Watts x 4 150 Watts x 2 (2) 20A / AWG 2.0" (5.08cm) 10.5" (26.67cm) 12.25" (31.11cm) Signal-to-Noise Ratio Input Sensitivity Crossover ( DX500.1/1000.1/2000.1 ) Crossover ( DX200.2/300.4 ) Crossover Frequency ( DX500.1/1000.1/2000.1 ) Crossover Frequency ( DX200.2/300.4 ) Channel Separation Subsonic Filter ( DX500.1/1000.1/2000.1 ) >70dB A-weighted 100mV - 5V 12dB/octave Low Pass only 12dB/octave High/Flat/Low Switch variable from 50Hz to 250Hz, Low Pass Only variable from 50Hz to 500Hz 50dB Variable 15 - 40Hz MODEL : DX500.1 / DX1000.1 / DX2000.1 (2 amplifiers strapped together) Continuous Power Rating (RMS) - Measured at 14.4 Battery Volts 4 £2 Load 500 Watts x 1 / 1000 Watts x 1 / 2000 Watts x 1 2 £2 Load 1000 Watts x 1 / 2000 Watts x 1 / 4000 Watts x 1 Specifications subject to change without notice 11...

Herunterladen

Geben Sie zwei Ziffern: