Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Elevation Audio Dateigröße: 6.73 mb Dateiname: Unterrichtssprache:

Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable thé screws to pull out from the panel due to road vibration or sudden vehicle stops. 8. Connect the source signal to the amplifier by plugging the RCA cables/high level inputs into the input jacks at the amplifier. 9. Connect the speakers. Strip the speaker wires 1/2" and insert into the speaker terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result. 10. Perform a final check of the completed system wiring to ensure that all connections are accurate. Check all power and ground connections for frayed wires and loose connections which could cause problems. NOTE: Follow the diagrams for proper signal polarity. Ç POWER INPUT 6 Installation From Source Unit -czTTEigfr~E)—cJ~T~b |-cflTlJ^FT^—cQTb RCA Inputs Amplifier From Source Unit -cflirbcfl~P- -cODicOO -cTTiï> -cT1T> -cflfr -cTTb RCA Inputs Amplifier From Source Unit -cnFTbcQin^H-cnirb. -cfiin=> RCA Inputs Amplifier DX200.2 DX300.4 DX500.1 DX1000.1 DX2000.1 Mono : DX500.1 I DX1000.1 / DX2000.1 Input 2Q min. oS ¿5 2-Channel : DX200.2 Input Input 2-Channel Bridged B Installation 4-Channel : DX300.4 4-Channel : DX300.4 Set as 3-Channel Bridged REMOTE LEVEL CONTROL (Only usable in LP Low Pass mode) (Model DX500.1/1000.1/2000.1) Mounting and installation 1. Find a location, either under the dash or near the center console, that gives easy access to the remote. 2. Using the screws supplied, install the mounting clip with the tabs towards the back. 3. Route the cable for the remote and connect to both the remote and amplifier. 4. Slip the remote onto the mounting clip until it snaps into place. o - o©o ■ « ^ _ QQ b û ooo Mounting 8 Operation ADJUSTING GAIN To adjust the gain setting, turn the amplifier gains all the way down. Turn the source unit volume up until distortion is audible and then turn it down a bit until the distortion is inaudible. This will be about two thirds all the way up on most source units. Next, turn the amplifier gain setting until once again distortion is audible and then back it down until the distortion is inaudible. NOTE: For a more in depth setting procedure, contact ELEVATION AUDIO dealer. ADJUSTING CROSSOVER (X-OVER] Model DX500.1 / DX1000.1 / DX2000.1 Turn the crossover adjustment knob all the way down. With the system playing at normal listening level, turn the crossover adjustment knob up slowly until the desired crossover point is achieved. All Other Models Placing the switch in the HIGH position sets the amplifier to the High Pass mode, enabling frequencies above the cut-off point to pass, adjustable between 50-250Hz. Placing the switch in the FLAT position sets the amplifier to the All Pass mode, preventing any crossover adjustment, allowing all frequencies to pass.. Placing the switch in the LOW position sets the amplifier to the Low Pass mode, enabling frequencies below the cut-off point to pass, adjustable between 50-250Hz. Turn the crossover adjustment knob all the way down. With the system playing, turn the crossover adjustment knob up slowly until the desired crossover point is achieved. SUBSONIC Model DX500.1 / DX1000.1 / DX2000.1 A variable 15-40Hz high pass filter designed to prevent frequencies below the audio range from being applied to the subwoofer from the amplifier. Set this to your personal preference while listening to the system. Crossover Gain O I O @Q * Ô :OOlboll O DX200.2 DX300.4 Crossover Gain Subsonic DX500.1 DX1000.1 DX2000.1 Crossover Gain Gain Crossover ^^_A- 9 Operation STRAPPING AMPLIFIERS CDX5CJO/I /DX1DOD.1 /DXSOaO.I ] The DX500.1/DX1...

Herunterladen

Geben Sie zwei Ziffern: