Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Lanzar Car Audio Dateigröße: 2.63 mb Dateiname: Unterrichtssprache:

The 12 o'clock position is a great starting point. EXAMPLE: Ifyou adjust the High Pass to 100Hz. the amplifier will not play trequencies below 100Hz but will play trequencies trom 100Hz to the chosen Low Pass trequency. -When in Low Pass/Bandpass operation, this setting acts as a low frequency cut off for your system reproduction aka Subsonic Filter. The point that you set it at cuts off any trequencies trom reproduction beyond this point. The 12 o'clock position is a great starting point. EXAMPLE: Ifyou adjust the High Pass to 25Hz. the amplifier will not play trequencies below 25Hz but will play frequencies from 25Hz to the chosen Low Pass frequency. -When in Flat/Full operation, the High Pass crossover is bypassed. BassEQ: This setting is a fIXed bass boost at 45Hz that is variable from 0-1 OdB. This feature provides impact to your bass, but if not adjusted correctly. it can be over used and cause damage to your speakers and amplifiers. It is best to slowly turn this setting clockwise until the desired punch is felt. it is not recommended to exceed the 12 o'clock position unless listening at a low volume or a low recording quali1y as this can result in high distortion and possibly clipping. Low Pass: The Low Pass control acts as a ceiling and doesn't allow frequencies to the right of the desired setting to be reproduced. Turning the potentiometer all the way to the right is a great starting point. EXAMPLE: Ifyou adjust the Low Pass to 120Hz. the amplifier will not play fTequencies above 120Hz but will play frequencies from 120Hz to the chosen Hi Pass or Subsonic trequency. -When in Hi Pass operation, this setting is bypassed. Level Control Setup: Ensuse that the level is turned completely to the left prior to turning the syetem on. Next you should insert a CD or cassette that you are familiar with to use as a reference, and turn the head unit volume control to about 80% of its full setting. The system sound level will of course be very low. and the following procedures will help you to match the amplifier input sensitivities properly to the head unit output signal level. It is important to match the amplifier LEVEL input sensitMty to the Radio/CD output sensitivity. This can be located in the Radio/CD manual. Ifthe Radio/CD output sensitivi1y is 2 volts. then adjust the amplifier LEVEL input to 2 volts. Ifyou are not sure what the Radio output sensitivi1y is. follow these general guide lines: Turn the level control up SlOWly, till you hear distortion, then back off a few degrrees on the control. If at any point your amplifier goes into protection, you will need to turn the level to the left a bit and then try again. If you reach a point where the output does not increase, stop turning the level control to the righe as the amplifier/speaker combo has reached its maxx output in this application. Zor:l way active systems lalll: Always start with the bass. or low frequency amplifier as a reference. by turning its control up to the point where distortion is audible. and back it olf some. Now adjust the level control for the highs or tweeter channels in a 2 way active system. to balance the highs to lows. In a 3 way active system, match the midrange level to the bass, and then the highs to the midrange and bass. It may be necessary to perform a few iterations of the midrange and highs level control settings to achieve a satisfactory sound balance. Sit bIIck and enjoy the music! - Lanzar MAX PRO SERIES AMPLIFIER FEATURES MODEL MAXP2760 MAXP2960 MAXP4260 Out Power Rating RMSat40hms 500Wx2 750Wx2 250Wx4 MAX at 4 Ohms 1000Wx2 1500Wx2 500Wx4 MAX at 4 Ohms Bridced 1200Wxl 3000Wxl 1000Wx2 RMSat 2 Ohms BOOWx2 1200Wx2 400Wx4 Miscellaneous Spec Soft Start Sound Yes Yes Yes Frequency Response -3dB 10Hz-40KHz 10Hz-40KHz 10Hz-40KHz Dampinc Factor >200 >200 >200 SIN Ratio(A-Weight) > 95dB > 95dB > 95dB THD & Noise <0.05% <0.05% <0.05% Channel Separation at I KHz >70dB >70dB >70dB Varible Input Level Control 0.2V-6.0V 0.2V-6.0V 0.2V-6.0V Input Impedance 20kQ 20kQ 20kQ Power and Diagnostic LED Power/Protect Power/Protect Power/Protect Protection(DC, Short, Thermal, Overload) Yes Yes Yes Power Supply. all MOSFET PWM Yes Yes Yes MOSFET Outputs Yes Yes Yes Crossover and Swlthchlng Input Selector Switch Crossover SfW for I +Z channel Hp/FULljLP-BP Hp/FULljLP-BP Hp/FULljLP-BP Variable Hi-pass / Subsonic Filter 40Hz-2kHz 40Hz-2kHz 40Hz-2kHz Variable Low-pass (Mono 24dB) 30Hz-150Hz 30Hz-150Hz 30Hz-150Hz Bass Boost at 45Hz 0-10dB 0-10dB 0-10dB Crossover SfW for 3+4 channel Variable Hi-pass 40Hz-2kHz 40Hz-2kHz 40Hz-2kHz Variable Low-pass/ (Mono 24dB) 30Hz-150Hz 30Hz-150Hz 30Hz-150Hz Bass Boost at 45Hz 0-10dB 0-10dB 0-10dB UneOutput Full Rance Full Rance Full Rance Unbalanced InputlRCAJackJ Yes Yes Yes Remote Control Yes Yes Yes Power Terminal 4-GA 4-GA 4-GA Speaker Terminal 8-GA 8-GA 8-GA Fuse Size 20Ax3 30Ax3 40Ax2 Dimensions (W x H x L) Inches 10. I 6-x2.56-xl 3.8610. 16-x2.56-xl 5.8310. 16-x2.56-xl 2.8 Note: Features subject to cha...

Herunterladen

Geben Sie zwei Ziffern: