Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: AT&T
Dateigröße: 275 kb
Dateiname: 9bcc1e9c-4b0d-d004-e188-35dea5e2d52d.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Please also read Part 1 – Important Product Information. AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones. © 2001 Advanced American Telephones. All rights reserved. Printed in China. 850005063 Issue 1AT&T 01/01 INSTALLATION Before You Install Choose a location for the answering system near a modular telephone jack and a standard electrical outlet not controlled by a wall switch. NOTE: If you do not want to connect a telephone, skip Step 2. Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111. Input: 120 V, 60 Hz. Output: 6V AC, 350 mA. Standard Electrical Outlet1 Connect the telephone line cord. 2 Connect the telephone (optional). 3 Connect the power cord. Strain-relief tab Modular Telephone Jack Turn System On/Off Before proceeding to set up features, press O to turn the system on. To turn the system off, press O again. 1 FEATURE SETUP Feature Setup 1 To enter Feature Setup mode, press 4 Press and release Sto set up the and hold Suntil the system next feature listed on the Feature announces “Number of rings.” Summary 2 Press and release Suntil the — OR — system announces the feature you Press and release P to exit want to set. Feature Setup. 3 Press and release or The new settings will be saved. until the system announces the setting you want. Refer to the Feature Summary for options. Feature Summary Feature/System Announces Options Announce Select Choose from Announcement A or Announce Only. “Selected announcement is...” • Select “Announcement A” when you want the system to record callers’ messages. Select “Announce Only” when you want the system to play an announcement and then hang up. • If you select “Announcement A” and do not record an announcement, the system plays a pre-recorded announcement: “Hello. Please leave a message after the tone.” • If you select “Announce Only” and do not record an announcement, the system will answer after 10 rings and announce “No announcement.” See “Record Your Announcement” under OPERATION for recording instructions. Ring Select Choose how many times the line will ring before the system answers a call. “Number of rings is...” • Set for 2 to 7 rings, or choose Toll Saver 2/4 or Toll Saver 4/6. • When set to Toll Saver 2/4, the system answers after four rings when you have no new messages and after two rings when you do. Toll Saver 4/6 causes the system to answer after six rings when you have no new messages and after four rings when you do. 2 FEATURE SETUP Feature Summary (cont’d) Feature/System Announces Options Remote Access Code Change the Remote Access Code to any three digit number from 500 to 999. “Remote Code is...” • The Remote Access Code, preset to 500, allows you to access many features of this answering system remotely from a touch tone phone. • The system will prompt you to repeat Steps 2 and 3 of Feature Setup until you have set all three digits. Announcement Monitor Choose ON to hear the announcement when your system answers a call. Choose OFF to have it silent on your end. (Your caller will still hear the announcement.) NOTE: Volume must be set to a level you can hear to use Announcement Monitor. Number Announce (Please see NOTE below.) When this feature is on, the system will announce the caller’s telephone number between the second and third rings. NOTE: When the Number Announce feature is on and Ring Select is set for two rings, the unit will answer after three rings to allow enough time for the system to announce the caller’s telephone number. Store Number (Please see NOTE below.) When this feature is on, the system announces the caller’s telephone number when it plays back a message. Accept Blocked Calls (Please see NOTE below.) Choose ON to have the system accept all calls. Choose OFF to have the system respond to “blocked” calls with the pre-recorded announcement, “We’re sorry, blocked calls to this number cannot be accepted,” and hang up without recording a message. Audible Message Alert When this feature is on, the system beeps every 15 seconds when you have new messages. NOTE: For this feature to work, you must subscribe to Caller Identification service from your telephone service provider. There is a fee for this service, and it may not be available in all areas. 3 OPERATION Set the Clock You must set the clock once so that the system announces the correct day and time with your messages. After this, if you subscribe to Caller ID, the system will automatically reset the clock each time new call information is received. (There is a fee for Caller ID service, and it may not be available in all areas.) Press P to exit at any time while setting the clock. 1 Press and hold C until the default day is announced. 2 To change the day setting, hold down or until the correct day is announced. Then release the button. 3 Press and release C. The current hour setting is announced. 4 Repeat Steps 2 and 3 to set the hours, minutes, and year. 5 The new day,...