Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
• Extend the FM transmitter antenna toward the FM receiving antenna for optimal reception. Black White White Black 18 | English Connection L FM/AM ANTENNA ( 5A ) B C + A B C A TV ANTENNA INPUT TO MONITOR UNIT FM-TX POWERTO MONITORTO TV TUNER L FM/AMANTENNA ( 3A ) PRK SW TO NAVIGATION AV 1 INPUT RVIDEO L (MONO) AV 2 INPUT RVIDEO L AV OUTPUT RVIDEO L Accessory BIgnition cable (Red) Parking sensor cable (Green) Ignition key switch Car fuse box (Main fuse)ACC Ground cable (Black) · (To car chassis) Battery Monitor Unit Connection cable (Provided with the Kenwood Navigation Unit) Video Box Unit Navigation Unit Connection cable (Provided with the KTC-V500P) KTC-V500P (Optional) For the sake of safety, be sure to connect the parking sensor. To parking brake detection switch harness of car Battery wire (Yellow) Audio/Visual input 1 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) Audio/Visual input 2 • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) Audio/Visual Output • Visual output (Yellow) • Audio left output (White) • Audio right output (Red) Accessory A• Do not leave this unit in any position where the FM transmitter antenna is bent or blocked off by metal parts. • Extend the FM transmitter antenna toward the FM receiving antenna for optimal reception. Black White White Black Installation Installation Installation for Monitor Unit ¦ Installation location and cleaning Select for installation a location where the stand can be placed completely horizontal or where the front edge of the support (petal-shaped part) can be attached horizontally as shown in Figure A. A BC Do not install in locations where the entire support is at a diagonal such as in Figure B or where the monitor unit is facing down such as in Figure C. • Thoroughly wipe away and dust or grease from the installation location using a cloth which has been soaked in a neutral cleaning agent and wrung out. Attach the stand after allowing the installation location to dry. ¦ Affixing the Cushion Affix the cushion to the monitor bracket. Bracket Accessory I English | 19 Installation for Monitor Unit ¦ Setting the Monitor Unit 1 Bend the stand support to conform to the shape of the installation location. 2 Adjust the shape of the support so that there is no rattling or gap when the stand is placed on the support. 3 Peel off the protective strip from the double- sided tape on the bottom of the stand and securely attach the stand. • Do not attach the double-sided tape more than once or touch the adhesive with your fingers as this will weaken its adhesive strength. • If the temperature of the surface of the installation location is low, warm it up using a heater or other means before attaching the stand. Low temperature may weaken the adhesive strength of the tape. • The supplied stand is specially intended for this product. Do not use it with another monitor. 4 Secure the stand (Accessory D) using the supplied tapping screw (Accessory G). 5 After attaching the stand, allow it to sit undisturbed for 24 hours. 6 Take care not to apply any force to the stand during this time. 7 Fully loosen the installation screws, align the slit on the rear of the unit with the installation shoe and slide the monitor unit onto the stand. 8 Adjust the height, horizontal angle and vertical angle of the monitor and securely tighten the installation screws. You can also adjust the monitor unit's forward position by loosening the angle adjustment knobs and adjusting the angle of the monitor unit's installation stand. Accessory DAccessory GProtective strip Tighten Loosen Installation surface Tighten Loosen • Attach the monitor to the bracket securely until it clicks. 20 | English Installation Installation ¦ Attaching the Harness Band Secure the cable to the bracket using the supplied harness band (Accessory J) . Accessory J ¦ Removing the Monitor Unit Raise the Release button. The Monitor Unit is unlocked, allowing you to detach it. Release button English | 21 Installation Installation Installation for Video Box Unit ¦ Securing to audio board 1 Use the screws (Accessory F) to fix the bracket (Accessory C) onto both sides of Video Box Accessory F Unit. Accessory C Accessory F 2 Use screws (Accessory E) to fix Video Box Unit Accessory E onto an audio board or another. ¦ Securing to pile carpet Peel the protective strips off of the velcro strips (Accessory H), attach them to the bottom of the Video Box Unit, and secure to the pile carpet. . • Please do not install the unit near the dashboard, the rear tray, or other important components. Doing so could lead to injury or accident should the unit come off due to a shock and strike a person or an important component. Tapping screws should be used for mounting. (Attachment with velcro strips, although easy, can come off with a shock.). .................................... Accessory H 22 | English Troubleshooting Guide Troubleshooting Guide What might appear to be a malfunction in your...