Stimmen - 0, Durchschnittliche Bewertung: 4 ( )

Hersteller: Linear Dateigröße: 256.56 kb Dateiname: Unterrichtssprache:

Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details. IMPORTANT !!! Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed. For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. Changes or modifications to the device may void FCC compliance. Infrequently used radio links should be tested regularly to protect against undetected interference or fault. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. Copyright © 2002 Linear Corporation 215633 E GND +12V LOW BAT STAT CH1 CH2 CH3 CH4 GND CH5 CH6 CH7 CH8 GND MODEL DXSR-1508 ONLY NEGATIVE +12 AUX ZONE 1 COM ZONE 2 ZONE 3 COM ZONE 4 EXAMPLE RELAY HOOK-UP CONTROL PANEL RECEIVER NOTES: 1. ZONES ARE NORMALLY OPEN WITH END-OF-LINE RESISTORS 2. LOW BATTERY AND STATUS OUTPUTS ARE COMBINED TO TRIGGER ZONE 4 AS TROUBLE TO +12 VOLTS TO RECEIVER OUTPUT N.C. N.O. COM 12 VOLT RELAY 1N4001 DIODE EXAMPLE 4-ZONE CONTROL PANEL HOOK-UP EXAMPLE BEEPER HOOK-UP TO RECEIVER OUTPUT TO +12 VOLTS PIEZO BEEPER EXAMPLE L.E.D. HOOK-UP 1K OHM L.E.D. TO +12 VOLTS TO RECEIVER OUTPUT JUMPER IN THIS POSITION (FACTORY SETTING) CAUSES A MOMENTARY 1 SECOND MINIMUM OUTPUT WITH EACH ACTIVATION SET OUTPUT JUMPERS FOR EACH CHANNEL USED JUMPER IN THIS POSITION CAUSES A TOGGLE OUTPUT, EACH ACTIVATION WILL CAUSE THE OUTPUT TO SWITCH FROM OFF TO ON, OR, ON TO OFF JUMPER REMOVED CAUSES OUTPUT TO LATCH UNTIL RESET BY A RESTORE TRANSMISSION (DXS-31 DOOR CLOSED) OR RESET BY PRESSING THE CHANNEL BUTTON (JUMPER CAN BE STORED ON SINGLE PIN) CUT STATUS JUMPERS FOR ANY CHANNELS THAT REQUIRE STATUS TRANSMISSION MONITORING USE SMALL CUTTERS TO CUT JUMPERS IF NORMALLY CLOSED OUTPUTS ARE REQUIRED, REMOVE THE OUTPUT POLARITY JUMPER MOMENTARY OUTPUT TOGGLE OUTPUT LATCHING OUTPUT 1 2 3 4 REMOVE THE PROGRAM JUMPER, THE CHANNEL DISPLAY SHOWS "P" BRIEFLY PRESS THE BUTTON FOR THE CHANNEL THAT THE TRANSMITTER IS GOING TO BE ADDED INTO, THE CHANNEL NUMBER SHOWS ON THE DISPLAY YOU HAVE 5 SECONDS TO ACTIVATE THE TRANSMITTER, THE ALARM LED WILL BLINK AFTER THE TRANSMITTER IS ENTERED, OR AFTER 5 SECONDS, THE CHANNEL DISPLAY WILL RETURN TO "P" REPEAT STEPS 2 & 3 FOR ADDITIONAL TRANSMITTERS (UP TO 32 TOTAL, WITH ANY MIX OF CHANNELS) THEN REPLACE PROGRAM JUMPER WHEN FINISHED NOTE: ON MULTI-BUTTON TRANSMITTERS, EACH BUTTON HAS A UNIQUE CODE, AND IS ADDED TO THE RECEIVER SEPARATELY, INTO ANY CHANNEL 1 2 3 COUNT THE NUMBER OF TIMES THE ALARM LED BLINKS, THIS IS THE NUMBER OF TRANSMITTERS PROGRAMMED INTO THE CHANNEL REPEAT STEPS 2 & 3 TO REVIEW OTHER CHANNELS REPLACE THE PROGRAM JUMPER WHEN FINISHED REMOVE THE PROGRAM JUMPER, THE CHANNEL DISPLAY SHOWS "P" PRESS AND HOLD THE BUTTON FOR THE CHANNEL TO REVIEW UNTIL THE ALARM LED STARTS TO BLINK, THEN RELEASE THE CHANNEL BUTTON 1 2 3 THE DISPLAY WILL CONTINUE TO SHOW THE CHANNEL NUMBER KEEP HOLDING DOWN THE CHANNEL BUTTON UNTIL THE ALARM LED FLASHES TWICE, SIGNALING THE CHANNEL HAS BEEN ERASED REPEAT STEPS 2 & 3 TO ERASE OTHER CHANNELS REPLACE THE PROGRAM JUMPER WHEN FINISHED PRESS AND HOLD THE CHANNEL BUTTON FOR THE CHANNEL TO ERASE, CONTINUE HOLDING DOWN THE BUTTON WHILE THE ALARM LED COUNTS THE NUMBER OF TRANSMITTERS KEEP HOLDING THE BUTTON DOWN REMOVE THE PROGRAM JUMPER, THE CHANNEL DISPLAY SHOWS "P" ALARM STATUS LOW BATT WHEN ALL OUTPUTS ARE RESTORED (NON-ALARM CONDITION), EITHER BY RESTORE TRANSMISSIONS OR BY MANUALLY RESETING LATCHED CHANNELS WITH THE CHANNEL BUTTONS, THE CHANNEL DISPLAY WILL RETURN TO THE BLINKING BAR THE CENTER BAR OF THE CHANNEL DISPLAY WILL BLINK WHILE THE RECEIVER IS IDLE THE DECIMAL POINT WILL LIGHT WHEN ANY INCOMING RADIO SIGNALS ARE PRESENT WHEN ANY CHANNELS ARE IN ALARM, OR HAVE ANY SUPERVISORY CONDITIONS, THE CHANNEL NUMBER(S) WILL SHOW ON THE CHANNEL DISPLAY, ADVANCING IN ASCENDING ORDER AS EACH CHANNEL NUMBER IS DISPLAYED, ITS CONDITION IS SHOWN ON THE THREE INDICATORS (ALARM, STATUS, OR LOW BATTERY) ALARM STATUS LOW BATT ALARM STATUS LOW BATT IF STATUS MONITORING IS ENABLED FOR A RECEIVER CHANNEL (BY CUTTING ITS STATUS JUMPER), A TRANSMITTER SENDING STATUS REPORTS MUST BE PROGRAMMED INTO THAT CHANNEL IF STATUS REPORTS ARE NOT RECEIVED FOR EIGHT HOURS, THE CHANNEL NUMBER WILL BE DISPLAYED, THE STATUS INDICATOR WILL LIGHT, AND THE STATUS OUTPUT WILL ACTIVATE NOTE: IF STATUS MONITORING IS ENABLED FOR A CHANNEL, ONLY PROGRAM ONE STATUS REPORTING TRANSMITTER INTO THAT CHANNEL STATUS MONITORING TRANSMITTER LOW BATTERY IF A LOW BATTERY REPORT IS RECEIVED F...

Herunterladen

Geben Sie zwei Ziffern: