Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Fotos und technische Daten Blaupunkt IVMS-6502 |
Anleitung Zusammenfassung
The manufacturer cannot accept responsibility for any damage caused as a result of improper fitting of this device. To avoid the risk of electrical shock, the device must be protected from water and moisture, and must not be opened. Dangerously high voltages are generated inside the device. We wish to point out that the right to claim against warranty is invalidated by any changes or modifications to the device that have not been explicitly approved by the manufacturer. Long-term operation or storage outside the specific temperature range can lead to a shortening of the useful life of the LC display. Safety notices Please observe the following safety notices during installation and whilst making the connections. -Disconnect the negative and positive terminals of the battery. -When doing so, please observe the safety notices provided by the vehicle manufacturer. -Before drilling the holes necessary for mounting the equipment and for laying cables, please make sure that concealed cables, the fuel tank and fuel lines cannot be damaged in the process! ACCESSORIES FITTING Accessories Accessories supplied -Connecting cable -Extraction tool -Operating instructions -Mounting plate -Adapter cable for a direct connection to an AV source -IR remote control IVRC-06 Available accessories -Monitor bracket 7608009300 The installation instructions are included with the bracket. Note regarding VIDEO IN/AUX: Only use original Blaupunkt accessory 7 607 001 510. Or else use a mono plug. Fitting Monitor installation Note: It is recommended that the fitting is carried out at a specialist workshop. Prepare the working area . Remove the headrest, and place it on a working surface that has been cleared and cleaned, where the further assembly procedures may be carried out. Note: Take appropriate action to ensure that the headrest is not damaged while fitting the monitor. Mark out the dimensions . Feel the covering of the headrest carefully to ensure that there are no invisible parts that would prevent the monitor from being fitted. Mark out the surface that needs to be cut out - its size must match that of the installation frame. ENGLISH 17 18 FITTING Carefully cut open the headrest cover Use a knife with an adjustable cutting depth to cut out the planned area. . Make the first cut inside the marked area at a point about 0.5 cm from one of the corners, then make a diagonal cut to a point about 0.5 cm from the opposite corner. . Make a similar cut between the other two diagonally opposed corners. Open the headrest and remove filling and other items . Carefully lift the covering material away from the cut area. . Adjust the cutting depth of the knife to about 2.5 cm, and cut into the headrest following a line about 0.5 cm inside the marked edge. . Carefully lift the filling material at one corner, and cut deeper into the material with the knife. . Remove the filling material in small pieces. . As you do this, lift one piece of the filling material, and ensure that the cut is being made to an even depth. To remove other pieces, use a Dremel saw or another suitable tool. . Insert the monitor to check that it will fit into the cut area, and make adjustments if necessary. DANSK 19 ENGLISH DEUTSCH FRANCAIS ITALIANO NEDERLANDS SVENSKA ESPANOL PORTUGUES FITTING Lay the cable through the headrest . Now pass the supplied cables through the opening so that they emerge from the underneath of the headrest. . If possible, cover the cable with a cable tunnel. . Now connect the power supply, ground and video signal cables, to check that the monitor is working. Insert the mounting frame in the headrest . Before connecting the monitor, pass the connecting cables through the holes provided in the mounting plate, as shown in the illustration. . Insert the mounting plate into the area that has been cut out, and fix it in place with appropriate fastenings. Inserting the monitor . Before connecting the monitor, pass the connecting cables through the holes provided in the mounting plate, as shown in the illustration. . Insert the monitor into the mounting plate, and attach it with appropriate fastenings. Monitor Mounting plate FITTING Check and adjust the monitor then apply the Velcro strips . Connect the monitor, place it temporarily in the cut-out, and place the headrest into position. . Check the various monitor settings such as brightness, headphone function, volume control and so on. . Then attach the Velcro strips to the rear of the monitor, and push the frame onto the headrest. Take care not to press the screen itself, and apply pressure only in the region of the frame. Example of a direct connection to a DVD player Adapter cable for a direct connection to an AV source DVD - Player (IVDP-01) Video outAVDigital inout Audio L outAudio R out Masse/GND +12V IVMS 5802/6502 Positive connection Connect the fuse holder to protect the positive cable (+12 V). The fuse holder should be connected to the positive terminal at a distance of max. 30 cm from the vehi...
Dieses Handbuch ist für folgende Modelle:Car Video - IVMS-5802 (396.78 kb)