Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
The hazard may come from something mechanical or from electric shock. Read the instructions carefully. Mechanical Electrical When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the corresponding instructions. Read the instructions carefully. This garage door opener is designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the safety instructions contained in this manual. 2 Safety An unbalanced garage door might not reverse when required and someone under the door could be seriously injured or killed. If your garage door binds, sticks or is out of balance, call for professional garage door service. Garage doors, door springs, cables, pulleys, brackets, and their hardware are under extreme tension and can cause serious injury or death. Do not tr y to loosen, mo ve or adjust them yourself! Ropes left on a garage door could cause someone to become entangled and killed. Remove all r opes connected to the door before installing and operating the opener. Identify the type and height of your door, any special conditions that exist, and any additional materials that may be required. Test Your Door for Balance Before you begin, complete the following test to make sure your door is balanced, and is not sticking or binding: • Lift the door about halfway as shown. Release the door. It should stay in place, supported entirely by its springs. • Raise and lower the door to see if there is any binding or sticking. To avoid damage to the garage door and opener, disable locks before installing and operating Use a wood screw or nail to hold locks in the "open" (unlocked) position. Operation at other than 120V 60 Hz will malfunction and damage. Hardware Supplied Rail Assembly Coupling Sleeve (1) Hex Screw 1/4"-20 x 5/8" (4) Nut 1/4" - 20 (4) Opener Installation Hex Screw 5/16"-18 x 7/8" (4) Lag Screw 5/16"-9 x 1-5/8" (2) Lag Screw 5/16"-18 x 1-7/8" (2) Carriage Bolt 5/16"-18 x 2-1/2" (2) Clevis Pin 5/16" x 2-3/4" (1) Sectional Door One-Piece Door Clevis Pin 5/16" x 1-1/4" (1) Clevis Pin 5/16" x 1" (1) Nut 5/16" - 18 (6) Lock Washer 5/16" (6) Screw 6AB x 1" (2) Insulated Staples (10) Ring Fastener (3) Handle Dry Wall Anchors (2) Rope Safety Reversing Sensor Installation Lag Screw 1/4 x 1-1/2" (4) Hex Screw 1/4-20 x 1-1/2" (2) Carriage Bolts 1/4" - 20 x 1/2" (4) Screw #10 - 32 x 3/8" (4) Lock Nut 1/4" - 20 (4) Lock Nut #10 x 32 (4) Wing Nut (2) Insulated Staples (20) 3 You may find it helpful to refer back to this page as you proceed with the installation of your opener. Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 20 for details. Support bracket & fastening hardware is required. See page 13. — — — — — — — — Door Center Header Wall Safety Reversing Sensor Floor must be level across width of door FINISHED CEILING Extension Spring Torsion Spring Access Door OR OR One-Piece Door-Extension Spring Header Wall Door Track Before you begin, survey your garage area to see whether any of the conditions below apply to your installation. SECTIONAL Door or ONE-PIECE Door with Track Installation Safety Reversing Sensor FINISHED CEILING Support bracket & fastening hardware is required. See page 13. Safety Reversing Sensor Header Wall Access Door Gap between floor and bottom of door must not exceed 1/4". ONE-PIECE Door Without Track Installation 5 Asembly 7 ASSEMBLY STEP 1 Fasten the Rail To the Power Unit NOTE: To aid in assembly and installation, the foam packing around the power unit. Remove it after Installation Step 5. • Working on a level surface, align the rail assembly the power unit, as shown. • Slip the coupling over the rail sprocket. Rail/Power Unit Bracket Power Unit Sprocket Rail Sprocket Rail Assembly Trolley Coupling Lock Nuts 1/4"-20 Opener Chassis Foam Packaging Hex Screws 1/4"-20x5/8" ASSEMBLY STEP 2 Install the Trolley 1/4" - 20 Lock Nut1/4" - 20 x 5/8" Hex Screw Hardware Shown Actual Size • Slide the rail through the power unit bracket until the coupling fits securely over the power unit sprocket. • Align the two screw holes in the rail with those in the power unit bracket. Insert two 1/4"-20x5/8" hex screws and lock nuts. Tighten securely with a 7/16" socket wrench. As illustrated above, slide the trolley onto and along the bottom of the rail until it snaps firmly in place. Be certain to install it facing correctly: the trolley release arm must be horizontal (lock position), with its arrow pointed away from the power unit. 6 ASSEMBLY STEP Attach the Rail Brackets 1/4"-20 • Align rail brackets to end as shown. Rail Lock Nuts • Insert two 1/4"-20 x 5/8" hex Tighten securely with a 7/16" socket. Brackets Rail 1/4"-20x5/8 Hex Screws 1/4" - 20 Lock Nut1/4" - 20 x 5/8" Hex Screw Hardware Shown Actual Size You ha...