Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: GTO Dateigröße: 3.5 mb Dateiname: Unterrichtssprache:

Disconnect operator ONLY when the gate is NOT moving. TO MANUALLY OPEN AND CLOSE THE GATE: 1. Lift quick release pins UP, then pull them OUT of chain brackets. 2. Lay chain down and manually slide gate to desired position. Series GTO, Inc. Tallahassee, Florida USA SL .. Conforms to UL 325 STANDARDS Certified to CAN/CSA-C22.2 No.247-92 • Fingers, hands, and loose clothing may be dragged into chain sprockets. • Fingers and hands can be injured by rotating sprockets. • Keep hands, fingers, and loose clothing away from chain and sprockets. WARNING! warning label located on top of control box product identification and manual operation instruction label installed on control box cover 7 IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Continued from page 7 These warning labels should be found at the locations specified below. If any of them are missing, immediately contact your installer for replacements. 1. KEEP CLEAR! Gate may move at any time. 2. Do not allow children to operate gate or play in gate area. 3. This gate is for vehicles only. Pedestrians must use a separate entrance. Moving Gate Can Cause Injury Or Death WARNING ! warning signs (2) to be installed on each side of the gate (3–5 feet above the bottom of the gate) • Fingers, hands, and loose clothing may be dragged into chain sprockets. • Fingers and hands can be injured by rotating sprockets. • Keep hands, fingers, and loose clothing away from chain and sprockets. WARNING! warning sign located (inside housing) over the top sprocket at back of operator • Adjusting limit switches with power on will activate gate. • Injury may result if fingers get caught under switch plate while adjusting switches. • Use extreme caution when adjusting switches. WARNING! warning label located on limit switch plate • Fingers, hands, and loose clothing may be dragged into chain sprockets. • Fingers and hands can be injured by rotating sprockets. • Keep hands, fingers, and loose clothing away from chain and sprockets. WARNING ! warning label located (inside housing) next to sprockets on back of operator 8 GTO PRO SL-1000 SERIES TECHNICAL SPECIFICATIONS GTO PRO SL-1000 SERIES TECHNICAL SPECIFICATIONS DRIVE • Powered by a 12 V motor with integral case hardened steel gear reduction to 90 rpm. Generates 155 in. lb. of torque at 12 V. Motor temperature range -30 °F to +160 °F. • Gate velocity: 1 ft/s. POWER • The PRO SL-1000 system is powered by a 12 Vdc, 7.0 Ah, sealed, rechargeable battery. • Battery charge for PRO SL-1000 is maintained by a 18 Vac (40 VA) transformer rectified to 14.5 Vdc through the GTO Control Board. Two (2) blade-style control board fuses rated for 15 A. NOTE: The transformer should not be connected directly to any battery. Transformer must be connected with a minimum of 16 gauge, multi-stranded, dual conductor, direct burial low voltage wire. NOTE: Do not replace fuses with higher ampere rated fuses; doing so will void the warranty and may damage the control board. • Battery charge maintained by GTO Solar Panel Charger: float voltage 14.5 Vdc output from a 193/8" x 151/4" silicon alloy panel. Generates minimum of 10 W at 600 mA. Gated diode on the control board prevents battery discharge. CONTROL • GTO microprocessor controlled board with temperature compensated circuits. Auto-memorization of digital transmitter code. Charging regulated by circuit on control board. "Sleep draw" is 40 mA; "active draw" is 2 to 5 A. • GTO remote-mounted RF receiver tuned to 318 MHz. • Limit controls are mechanical. Normally open contact. • Adjustable auto-close timer (OFF to 120 s), inertia, and obstruction sensitivity using three (3) potentiometers. • Power terminal block accommodates a transformer and solar panels. • Operator terminal blocks accommodate safety edges and photoelectric sensors for opening and closing modes. • Fully compatible accessory terminal block provides connections for safety loops, wands, intercoms, card readers, phone systems, etc. • DIP switches simplify setup of gate operator. • audio entrapment alarm sounds if unit obstructs twice while opening or closing. OPERATIONAL CAPACITY • The GTO/PRO SL-1000 and GTO/PRO SL-1000B will handle gates weighing up to 500 lb. (226.7 kg) and up to 30 ft. (9.14 m) in length (per leaf) if the proper installation procedures have been followed. Note that ball bearing rollers and covers should be used on all gates. • The GTO/PRO SL-1000 series operators are capable high volume cycling; however, the total cycles per day will depend on the motor current and efficiency of the gate installation (see chart below). For questions relating to specific applications and for information regarding cycling duty when charged by solar panels, call the GTO Service Department at (800) 5431236. Gate Capacity Chart for SL-1000 Series (estimated number of cycles based on use with a transformer) Gate Opening 20 ft. 120 110 100 90 16 ft. 140 130 120 110 12 ft. 160 150 140 130 8 ft. 180 170 160 150 200 lb. 300 lb. 400 lb. 500 l...

Herunterladen

Geben Sie zwei Ziffern: