Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
E
E
N
N
Installation Guide
G
G
L
L
I
I
S
S
H
❐ Identify All Leads
If your car is not wired for an audio unit:
H
Go to the fuse block and find the fuse port for the
13
WARNING
The first step in installation is to identify all the car
battery, usually marked BAT.
14
wires you’ll use when hooking up your sound sys-
This installation information is designed for experienced installers and is not in-
tem.
Speakers
tended for non-technical individuals. It does not contain warnings or cautions of po-
As you identify each wire, we suggest that you label
Identify the car speaker leads. There are two leads
it using masking tape and a permanent marker.
for each speaker which are usually color coded.
tential dangers involved in attempting to install this product.
This will help avoid confusion when making con-
A handy way to identify the speaker leads and the
nections later.
speaker they are connected with is to test the leads
Any attempt to install this product in a motor car by anyone other than qualified in-
using a 1.5 V AA battery as follows.
staller could cause damage to the electrical system and could result in serious per-
Note: Do not connect the power connector to the
Hold one lead against one pole of the battery and
sonal injury or death.
stereo unit until you have made all connections. If
stroke the other lead across the other pole. You will
there are no plastic caps on the stereo hooking
hear a scraping sound in one of the speakers if you
❐ Installation Hardware
If you encounter problems, please consult your
wires, insulate all exposed leads with electrical tape
are holding a speaker lead.
nearest professional installer.
until you are ready to use them. Identify the leads in
If not, keep testing different lead combinations until
No.
Item
Diagram
Q’ty
the following order.
you have located all the speaker leads. When you
Caution: This unit operates with a 12 V DC neg-
Power Lead
label them, include the speaker location for each.
q
Mounting collar
1
ative ground auto battery system only. Do not
If your car has a radio or is pre-wired for one:
attempt to use it in any other system. Doing so
Antenna Motor
Cut the connector wires one at a time from the plug
could cause serious damage.
If your car is equipped with an automatic power an-
w
Hex. nut (5 mmø)
1
(leaving the leads as long as possible) so that you
tenna, identify the car motor antenna lead by con-
can work with individual leads.
necting one bulb tester lead to the car battery lead
e
Rear support strap
1
Before you begin installation, look for the items
and touching the remaining exposed wires from the
which are packed with your unit.
cut radio connector plug one at a time. You will
Tapping screw
hear the antenna motor activate when you touch
r
• Warranty Card…Fill this out promptly.
(5 mmø×16 mm)
1
the correct wire.
• Panasonic Servicenter List for Service Directory
…Keep for future reference in case the product
Antenna
t
Mounting bolt (5 mmø)
1
needs servicing.
The antenna lead is a thick, black wire with a metal
• Installation Hardware…Needed for in-dash in-
Turn the ignition on to the accessory position, and
plug at the end.
stallation.
ground one lead of the test bulb to the chassis.
y
Power connector
1
Touch the other lead of the test bulb to each of the
❐ Connect All Leads
❐ Required Tools
Removable face plate
exposed wires from the cut radio connector plug.
Now that you have identified all the wires in the car,
u
case
1
You’ll need a screwdriver, a 1.5 V AA battery, and
Touch one wire at a time until you find the outlet
you are ready to begin connecting them to the
the following:
that causes the test bulb to light.
stereo unit wires. The wiring diagram (➡ page 28)
i
Trim plate
1
12 V DC
Electrical
Side-cut
Now turn the ignition off and then on. If the bulb
shows the proper connections and color coding of
Test bulb
tape
pliers
also turns off and on, that outlet is the car power
the leads.
o
lead.
We strongly recommend that you test the unit be-
Dismounting plate
2
fore making a final installation.
If your car is not wired for an audio unit:
You can set the unit on the floor and make tempo-
Go to the fuse block and find the fuse port for radio
❐ Overview
rary connections to test the unit. Use electrical tape
(RADIO), accessory (ACC), or ignition (IGN).
This product should be installed by a professional.
to cover all exposed wires.
❐ Dashboard Specifications
Battery Lead
However, if you plan to install this product yourself,
your first step is to decide where to install it. The
Thickness Min. 3⁄16" (4.75 mm)
If your stereo unit has a yellow lead, you will need
Important: Connect the red power lead last,
instructions in these pages will guide you through
Max. 7⁄32" (5.56 mm)
to locate the car’s battery lead. Otherwise you may
after you have made and insulated all other con-
ignore this procedure. (The yellow battery lead pro-
nections.
the remaining steps:
vides continuous power to maintain a clock, memo-
(Please refer to the “WARNING” statement above.)
23⁄32" (53 mm)
ry storage, or other function.)
Ground
• Identify and label the car wires.
If your car has a radio or is pre-wired for one:
Connect the black ground lead of the power con-
• Connect the car wires to the wires of the power
connector.
75⁄32" (182 mm)
With the ignition and headlights off, identify the car
nector to the metal car chassis.
battery lead by grounding one lead of the test bulb
• Install the unit in the dashboard.
to the chassis and checking the remaining exposed
• Check the operation of the unit.
wires from the cut radio connector plug.
22
23
CQ-DP133U/DP103U/DPX153U
CQ-DP133U/DP103U/DPX153U
...Dieses Handbuch ist für folgende Modelle:
Car-Receiver - CQDP133U (1.64 mb)
Car-Receiver - CQDPX153U (1.64 mb)