Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
(Hours blink.) (Hours set.) (Minutes blink.) (Minutes set.) (End.) Initial Time qPress [DISP] (clock). "AdJ" is displayed when the clock is not adjusted. Time Reset Press and hold [DISP] (display) for more than 2 seconds to activate the time setting mode to reset the time. Then, repeat steps eto y. [DISP] (clock) [k TUNE], [l TUNE] (Hours, minutes) Adjustable range: 1 to 15 (by 1 step) Balance center Adjustable range: 1 to 15 (by 1 step) Fader center (Only for CQ-DPX153U) Sub Woofer: Adjustable range (level): MUTE (0) to 8 (Only for CQ-DPX153U) Push Turn the knob clockwise or conterclockwise to change each level. w E N G L I S H 3 E N G L I S H 3 Radio Radio Mode Press [SRC] (source) to change Radio CD player Preset Station Setting Display Change (When a CD is inserted.) Up to 6 stations each can be saved in the FM1, Press [DISP] (display) to switch to the clock display. FM2, FM3 and AM preset station memories. E N G L I S H 4 POWER REP CLOCK CQ-DP133U DISP LOUDMUTE 7 8 9 10 11 12 SCAN 1 2 3 4 6 APM SRC5 VOLU M E PUSHSEL TUNE D•M TRACK BAND SRC Manual Tuning [l TUNE]: Higher frequency [k TUNE]: Lower frequency Seek Tuning Press and hold ... [l TUNE]: Higher frequency [k TUNE]: Lower frequency Tuning will automatically stop when the signals of the next broadcast station are received. Band Press [BAND] to change the band. Direct Memory(D·M) Your favorite FM/AM radio station can be memorized in the [D·M] button and you can call back radio stations just by pressing the button whatever the current sound source is, even if the power is off. to the radio mode. FM Stereo indicator Recalling the Direct Memory Memorize Select the station in Radio mode (a above) Press [D·M]. (Press again to cancel) .The direct memoried station is received. D-M Press and hold [D·M] until D·M indicator blinks. Default : FM 87.9 MHz D-M blinks e Release [D·M] button. Then, frequency display will blink and new station will be overwritten on existing saved station. D-M Note: Existing saved stations are overwritten with new stations after following this procedure. Frequency Clock display POWER REP D•M CLOCK CQ-DP133U TRACK TUNE LOUDMUTE 7 8 9 10 11 12 SCAN APM SRC VOLU M E PUSHSEL DISP 1 2 3 4 BAND 65 Band Press [BAND] to select a desired band. (. page 12) q Preset buttons from [1] to [6] w Auto Preset Memory (APM) Press and hold [BAND] (APM: auto preset memory) for more than 2 seconds. • The 6 stations with good reception will be automatically saved in the memory under preset buttons from [1] to [6]. • Once set, the preset stations are sequentially scanned for 5 seconds each. Manual Preset Memory Use manual or seek tuning to find a station. (. page 12) Press and hold one of the preset buttons from [1] to [6] until the display blinks once. blinks once Preset Station Calling Caution: To ensure safety, never attempt to preset sta- Press the corresponding preset button from tions while you are driving. [1] to [6] to tune in a preset station. CQ-DP133U/DP103U/DPX153UCQ-DP133U/DP103U/DPX153U E N G L I S H 5 E N G L I S H 5 CD Player Disc Insert and Playback Disc insert Playback will start automatically after the player recognized the loaded disc as an ordinary music CD. (When a CD-R or CD-RW which has CD-DA formatted data as the same as an ordinary music CD is loaded, this player recognizes it as an ordinary music CD.) “LOAd” will be displayed until the disc is loaded. Notes: • Do not insert a disc when “DISC” indicator lights. DISC • The power will be turned on automatically when a disc is loaded. Stop and Disc Eject Press [u] (eject) to stop CD play and eject the disc. During disc ejection, “EJ” (eject) will be displayed. Listening to a CD CD Player Mode (When a CD is in the player.) POWER REP D•M CLOCK CQ-DP133U TRACK TUNE LOUDMUTE 7 8 9 10 11 12 SCAN 1 2 3 4 6 APM BAND SRC 5 VOLUM E PUSHSEL DISPSRC Display Change Press [DISP] (display) to switch to the clock display. Radio CD player (When a CD is inserted.) TRACK DISC Press [SRC] (source) to change to the CD play mode. Playback will start automatically.