Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
E
E
N
N
Installation Guide
G
G
L
L
I
I
S
S
If your car is not wired for an audio unit:
H
❐ Identify All Leads
H
Go to the fuse block and find the fuse port for the
The first step in installation is to identify all the car
19
WARNING
20
battery, usually marked BAT.
wires you’ll use when hooking up your sound sys-
This installation information is designed for experienced installers and is not in-
tem.
Speakers
As you identify each wire, we suggest that you label
Identify the car speaker leads. There are two leads
tended for non-technical individuals. It does not contain warnings or cautions of po-
it using masking tape and a permanent marker.
for each speaker which are usually color coded.
tential dangers involved in attempting to install this product.
This will help avoid confusion when making con-
A handy way to identify the speaker leads and the
nections later.
speaker they are connected with is to test the leads
Any attempt to install this product in a motor car by anyone other than qualified in-
using a 1.5 V AA battery as follows.
staller could cause damage to the electrical system and could result in serious per-
Note:
Hold one lead against one pole of the battery and
≥ Do not connect the power connector to the stereo
sonal injury or death.
stroke the other lead across the other pole. You will
unit until you have made all connections. If there
hear a scraping sound in one of the speakers if you
are no plastic caps on the stereo hooking wires,
are holding a speaker lead.
❐ Installation Hardware
If you encounter problems, please consult your
insulate all exposed leads with electrical tape until
If not, keep testing different lead combinations until
nearest professional installer.
you are ready to use them. Identify the leads in
No.
Item
Diagram
Q’ty
you have located all the speaker leads. When you
the following order.
Caution:
label them, include the speaker location for each.
1
Mounting collar
1
≥ This unit operates with a 12 V DC negative
Power Lead
Antenna Motor
ground auto battery system only. Do not at-
If your car has a radio or is pre-wired for one:
If your car is equipped with an automatic power an-
Cut the connector wires one at a time from the plug
2
Hex. nut (5 mm
tempt to use it in any other system. Doing so
·)
1
tenna, identify the car motor antenna lead by con-
could cause serious damage.
(leaving the leads as long as possible) so that you
necting one bulb tester lead to the car battery lead
can work with individual leads.
3
Rear support strap
1
Before you begin installation, look for the items
and touching the remaining exposed wires from the
which are packed with your unit.
cut radio connector plug one at a time. You will
hear the antenna motor activate when you touch
4
Tapping screw
1
≥ Warranty Card…Fill this out promptly.
the correct wire.
(5 mm·a16 mm)
≥ Panasonic Servicenter for Service Directory
Antenna
5
Mounting bolt (5 mm
…Keep for future reference in case the product
·)
1
Turn the ignition on to the accessory position, and
The antenna lead is a thick, black wire with a metal
needs servicing.
ground one lead of the test bulb to the chassis.
plug at the end.
≥ Installation Hardware…Needed for in-dash in-
6
Power connector
1
stallation.
Touch the other lead of the test bulb to each of the
❐
exposed wires from the cut radio connector plug.
Connect All Leads
❐ Required Tools
Touch one wire at a time until you find the outlet
Now that you have identified all the wires in the car,
7
Removable face plate
1
You’ll need a screwdriver, a 1.5 V AA battery, and
that causes the test bulb to light.
you are ready to begin connecting them to the
case
the following:
stereo unit wires. The wiring diagram (➡ pages
Now turn the ignition off and then on. If the bulb
8
Trim plate
1
12 V DC
Electrical
Side-cut
34j37) shows the proper connections and color
also turns off and on, that outlet is the car power
Test bulb
tape
pliers
coding of the leads.
lead.
We strongly recommend that you test the unit be-
If your car is not wired for an audio unit:
fore making a final installation.
❐ Overview
Go to the fuse block and find the fuse port for radio
You can set the unit on the floor and make tempo-
This product should be installed by a professional.
(RADIO), accessory (ACC), or ignition (IGN).
rary connections to test the unit. Use electrical tape
However, if you plan to install this product yourself,
to cover all exposed wires.
Battery Lead
your first step is to decide where to install it. The
If your stereo unit has a yellow lead, you will need
instructions in these pages will guide you through
❐ Dashboard Specifications
Important:
to locate the car’s battery lead. Otherwise you may
the remaining steps:
Thickness
≥ Connect the red power lead last, after you
ignore this procedure. (The yellow battery lead pro-
(Please refer to the “WARNING” statement
Min. 3⁄16z (4.75 mm)
have made and insulated all other connec-
vides continuous power to maintain a clock, memo-
above.)
Max. 7⁄32z (5.56 mm)
tions.
ry storage, or other function.)
≥ Identify and label the car wires.
23⁄32z (53 mm)
If your car has a radio or is pre-wired for one:
Ground
≥ Connect the car wires to the wires of the power
With the ignition and headlights off, identify the car
Connect the black ground lead of the power con-
connector.
battery lead by grounding one lead of the test bulb
nector to the metal car chassis.
≥ Install the unit in the dashboard.
75⁄32z (182 mm)
to the chassis and checking the remaining exposed
≥ Check the operation of the unit.
wires from the cut radio connector plug.
28
29
CQ-DF801/DFX701/DF601U
CQ-DF801/DFX701/DF601U
...Dieses Handbuch ist für folgende Modelle:
Car-Receiver - CQDF801U (834.49 kb)
Car-Receiver - CQDFX701U (834.49 kb)