Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
NOTE Turning the volume up, or turning it all the way down deactivates the attenuator function. Loudness This function amplifies low and high tones when the volume is turned down. The LOUD indicator lights up, when the loudness function is on. Turning Loudness On/Off: Hold down the LOUD button for one second or more to switch the loudness on and off. NOTE The loudness function does not affect non-fading pre-out. — 7— English General features Audio Control Adjust various parameters 1 Press the AUD button 2 Selecting mode Press either the FM or AM button. Each time the button is pressed, change. Please refer to the following for the adjustment modes. NOTE Source tone memory Each source (CD, MD, FM, AM, and disc changer) memory in which to store the bass, treble and N-The settings made for a particular source are then automatically whenever you use that source (e.g., FM the tone settings made for FM, AM for AM, etc.). 3 Adjust each mode Press the 4/ . button. Look at the table to adjust the mode being displayed. 4 Press the AUD button to end the control mode. "dB" : Recalling the kenwood preset sound setting Press the preset buttons (#1-6). Settings: #1;Flat, #2;Rock, #3;Pops/Top40, #4;Jazz, #5;Easy, #6;Scan of #1-5 NOTE • This mode is available only when the Sound coordinate system is on. (page 35) • You can call the following settings with this function; bass centre frequency, bass level, bass quality factor, bass extension, treble centre frequency, and treble level setting. Their setting values are different depending on the setting of the mobile preset plan mode. "Bass Frq" : Adjust the centre frequency of the bass. Setting values: 60 / factor is set to 1.00, 1.25 quality factor is set to 2.00) NOTE This mode is available only when on. (page 35) "Bass" : Adjust the bass level. Setting values: - 8 – + 8 "Bass Q" : Adjust the Bass quality factor. Setting values: 1.00 / 1.25 / 1.50 / 2.00 NOTE This mode is available only when the Sound coordinate system is on. (page 35) "Bass EXT" : Switch the Bass Extend mode on/off. Setting values: ON / OFF (When the bass extend mode is set to on, low frequency response is extended by 20%.) NOTE This mode is available only when the Sound coordinate system is on. (page 35) — 8— "Tre Frq" : Adjust the centre frequency of the treble. Setting values: 10.0 NOTE This mode is available only on. (page 35). "Tre" : Adjust the treble level. Setting values: - 8 – + 8 "Balance" : Adjust the balance level. Setting values: Left 15 – Right 15 "HPF Front" : Adjust the frequency of the High-pass filter for front output. Setting values: Through / 40Hz / 60Hz 150Hz / 180Hz / 220Hz NOTE You can separately set the high-output, including preouts. The high-non-fading preout. The factory default and rear output are "Through" . "HPF Rear" : Adjust the frequency of the High-pass filter for rear output. Setting values: Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz / 150Hz / 180Hz / 220Hz NOTE You can separately set the high-pass filter for front and rear output, including preouts. The high-pass filter does not affect the non-fading preout. The factory default settings for front output "Fader" : Adjust the fader level. and rear output are "Through" . Setting values: Front 15 – Rear 15 "NFpre Level" : Adjust the Non-fading output level. Setting values: - 15 – + 15 NOTE Not available during the Dual zone system is on. "LPF NFpre" : Adjust the frequency of the Low-pass filter for Non-Fading output. Setting values: 50 Hz / 80 Hz / 120 Hz / Through NOTE Not available during the Dual zone system is on. — 9— General features Mobile Preset English "NFpre Phase" : Adjust the phase for Non-Fading output. Setting values: Normal NOTE Not available during the Dual "VOL OFFSET" : Set the sound level of the each source selected by adjusting the level difference between the basic sound level and the required level. Setting values: - 8 – 0 This function allows with the sound coordinate speakers. 1 Press the SRC button repeatedly "ALL OFF" is displayed when the 2 Press the AUD button to enter the 3 Press either the 4 or . button to select the type of speaker. The setting switches as follows. Off / For the OEM speaker / For 6/6x9 in. For 5/4 in. speaker 4 Press the AUD button to end the mobile preset NOTE • This mode is available only when the Sound coordinate is on. (page 35) • When you change the setting of type of speaker, the bass Hold down a preset button (#1-6) for two seconds or more. Storing your sound settings: treble tone settings are returned to original levels. NOTE • This setting can be made only when the Sound coordinate system is on. (page 35). • The settings you can preset are, bass centre frequency, bass level, bass quality factor, bass extension, treble centre frequency, and treble level. Non-Fading Output Turning non-fading output On/Off : Hold down the NF button for one second or more to set the function ON or OFF. "NF ON" is displayed when the non-fading output is set ON. Recalling your sound setting...