Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenwood Dateigröße: 682.3 kb Dateiname: Unterrichtssprache:

2 Press the NAME.S button for at least "NAME SET" is displayed once the station is entered. The cursor will blink in the position where 3 Press either the 4 or . button to move the cursor to the desired position. The 4 button moves the cursor to the left, and the . button to the right. You can also move the cursor left or right by pressing 4 or . buttons, respectively, on the remote. 4 Each time the 38 button is pressed, the characters to be entered change as listed below. Press the FM or AM button to display the desired character. Characters that can be displayed are as follows. Alphabet (upper case): A ~ Z Alphabet (lower case): a ~ z Numerals and symbols: 0~9 @ ” ‘ ` % & * + - = , . / \ < > [ ] Special characters: aaeeiioouuNC®.‹ fl aaeeiioouunc©.› fi NOTE Direct Alphabet Input (Function of remote with number/letter entry buttons) Direct input can be made of letters (alphabetical) with the letter entry buttons on the remote. Example: Use the following table to enter the name "DANCE" . Character Button to press # Times pressed “ D” #3 1 “ A” #2 1 “ N” #6 2 “ C” #2 3 “ E” #3 2 5 Continue steps 3 and 4 until all the characters the name. NOTE You can enter up to eight characters for each name. 6 Assigning Names Press the NAME.S button on the unit or the OK button remote. The name of the station is stored in memory, and the Station Name Preset mode ends. Also, if you make no input for 10 seconds, the name will be stored up to the point that you have entered, and the mode ends. NOTE • You can assign names to up to 32 FM stations and 16 AM stations. • All the station names will be erased if you press the Reset button. • If you want to change the name of a station, first display the name of the station (following steps 1 and 2 above), then change the letter(s) that you want by following steps 3 and 4. Switching Display for Tuner You can change the display used when listening to the radio. Changing the Display: Each time you press the DISP button, the display changes as — 18 — CD/External disc control features follows: Station frequency SNPS name (only when being preset) — 19 — SCAN RDM REP DISP/ NAME.S M.RDM AM FM 0 4 . 38 SRC KDC-X617/KDC-516S/KDC-57MR KDC-V6017 IN indicator IN indicator Track number Track time Disc number Track number Track time Disc number Release button CD/External Playing CDs NOTE English Playing CDs: Press the release button the CD insertion slot. Holding the CD with the labeled slot. The CD will start playing. faceplate with your hand until it The IN indicator will light when a CD • When you load a CD try to insert the CD may CD out for a moment and • While the control panel is 0, ATT, , and SRC. 2CAUTION When inserting a CD, make sure the CD drawn in before pushing back the faceplate. might scratch the CD. Playing CDs Already Inserted: Press the SRC (source) button repeatedly to select mode. "CD" is displayed when the CD mode has been selected. The CD will start playing. Pausing and Restarting CD Play: Press the 38 button to make the disc pause. Press the same button again to start play again. Eject: Press the release button and slide open the faceplate. Press the 0 button. The CD stops playing and ejects from the slot. Push back the bottom of the faceplate with your hand until it locks. 2CAUTION • Do not attempt to insert a CD into the slot if another one is already there. • The unit can only play 5 in. CDs. If you insert a 3 in. CD, it will get stuck inside and can cause the unit to malfunction. • When the faceplate has been slid open, it might interfere with the shift lever or something else. If this happens, pay attention to safety and move the shift lever or take an appropriate action, then operate the unit. • Do not use the unit with the faceplate in the open condition. Doing so will cause breakdown. Playing Other Disc mode This function permits the connection of the playing of discs other than the loaded unit). Playing Discs: Press the SRC button repeatedly to select the external control mode. The disc will start playing. NOTE The external disc control mode will differ, depending on the unit that is connected. Mode Display Examples • "CD2" ...when a CD player is connected • "DISC" ...when a disc changer is connected • "DISC-1" , "DISC-2" ...when two disc changers are connected Pausing and Restarting Disc Play: Press the 38 button to make the disc pause. Press the same button again to start play again. NOTE • When one disc has finished playing its last track, the next disc in the changer will start playing. When the last disc in the changer has finished, the player will return to the first disc and start playing it. • Disc #10 is displayed as "0". — 20 — Switching Display Switch the display Switching Display for Each time you press the play switches as follows: Track time Disc name (DNPS) (only when being preset) Disc title (Units featuring CD text/MD only) (KDC-516S/57MT : Function of disc changers) Track title (Units featuring CD text/MD only) (KDC-516S/57MT : Function of disc ...

Herunterladen

Geben Sie zwei Ziffern: